Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0441741 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly*1

·

Panoramic View Monitor System*2

·

Radio and display receiver assembly


Navigation System A

*1: w/ Parking Assist Monitor System

*2: w/ Panoramic View Monitor System


WIRING DIAGRAM

w/ Parking Assist Monitor System
E422634E06
2.26,3.021 3.635,3.219 1.375,0.198 10 false *: Shielded 0.458,2.917 1.656,3.302 1.198,0.385 10 false Radio and Display Receiver Assembly 1.021,2.417 1.479,2.635 0.458,0.219 10 false CSLD 1,2.052 1.5,2.271 0.5,0.219 10 false CGND 1.229,1.104 1.615,1.302 0.385,0.198 10 false V- 1.229,0.604 1.615,0.802 0.385,0.198 10 false V+ 1.125,1.604 1.51,1.802 0.385,0.198 10 false CA+ 1.49,1.51 1.875,1.708 0.385,0.198 10 false 30 3.406,2.292 3.792,2.49 0.385,0.198 10 false * 5.438,2.771 6,2.958 0.563,0.188 10 false Y2 5.521,1.615 5.906,1.813 0.385,0.198 10 false CB+ 5.521,0.604 5.906,0.802 0.385,0.198 10 false CV+ 5.521,1.115 5.906,1.313 0.385,0.198 10 false CV- 5.521,2.083 6.031,2.292 0.51,0.208 10 false CGND 5.333,1.5 5.719,1.698 0.385,0.198 10 false 6 5.313,0.5 5.698,0.698 0.385,0.198 10 false 3 5.323,1 5.708,1.198 0.385,0.198 10 false 2 5.333,1.948 5.719,2.146 0.385,0.198 10 false 5 0.458,2.75 0.844,2.948 0.385,0.198 10 false H80 1.5,0.5 1.885,0.698 0.385,0.198 10 false 28 1.5,1 1.885,1.198 0.385,0.198 10 false 29 1.5,1.958 1.885,2.156 0.385,0.198 10 false 27 1.5,2.302 1.885,2.5 0.385,0.198 10 false 26 5.438,2.958 6.896,3.396 1.458,0.438 10 false Rear Television Camera Assembly

w/ Panoramic View Monitor System
E402603E18
5.073,1.125 5.531,1.323 0.458,0.198 10 false NS+ 5.073,1.542 5.531,1.74 0.458,0.198 10 false NS- 5.073,1.938 5.531,2.135 0.458,0.198 10 false NSG 1.854,1.094 2.313,1.292 0.458,0.198 10 false V+ 1.865,1.552 2.323,1.75 0.458,0.198 10 false V- 1.083,2.49 2.281,2.885 1.198,0.396 10 false Radio and Display Receiver Assembly 4.938,2.438 6.458,2.844 1.521,0.406 10 false Parking Assist ECU 2.177,1.021 2.635,1.219 0.458,0.198 10 false 28 2.177,1.458 2.635,1.656 0.458,0.198 10 false 29 0.302,3.302 1.552,3.583 1.25,0.281 10 false *: Shielded 3.542,1.802 4,2 0.458,0.198 10 false * 4.781,1.448 5.24,1.646 0.458,0.198 10 false 28 4.813,1 5.271,1.198 0.458,0.198 10 false 27 4.823,1.833 5.281,2.031 0.458,0.198 10 false 29 1.083,2.302 1.542,2.5 0.458,0.198 10 false H80 4.927,2.26 5.385,2.458 0.458,0.198 10 false O25

PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Parking Assist Monitor System A
w/ Panoramic View Monitor System B



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the Y2 rear television camera assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H80,Y2)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(Y2)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

H80-30 (CA+) - Y2-6 (CB+) Always Below 1 Ω
H80-28 (V+) - Y2-3 (CV+) Always Below 1 Ω
H80-29 (V-) - Y2-2 (CV-) Always Below 1 Ω
H80-27 (CGND) - Y2-5 (CGND) Always Below 1 Ω
H80-26 (CSLD) - Body ground Always Below 1 Ω
H80-30 (CA+) or Y2-6 (CB+) - Body ground Always 10 kΩ or higher
H80-28 (V+) or Y2-3 (CV+) - Body ground Always 10 kΩ or higher
H80-29 (V-) or Y2-2 (CV-) - Body ground Always 10 kΩ or higher
H80-27 (CGND) or Y2-5 (CGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

Pre-procedure1

a.

Reconnect the H80 radio and display receiver assembly connector.


Procedure1

b.
E366062C69
1.427,0.198 1.917,0.479 0.49,0.281 0.542,1.073 1.042,1.344 true 0.771,1.76 1.167,1.375 true 1.333,1.875 1.438,1.375 true 1.552,0.25 1.865,0.448 0.313,0.198 10 false H80 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.344,0.875 0.802,1.073 0.458,0.198 10 false CA+ 0.635,1.771 0.948,1.969 0.313,0.198 10 false V- 1.156,1.896 1.771,2.094 0.615,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H80)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H80-29 (V-) - Body ground Always Below 1 Ω
H80-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H80)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H80-30 (CA+) - H80-27 (CGND) Ignition switch ACC 5.5 to 7.05 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.INSPECT REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT REAR TELEVISION CAMERA ASSEMBLY

Pre-procedure1

a.

Reconnect the Y2 rear television camera assembly connector.


Procedure1

b.
E366062C70
1.5,0.25 1.917,0.5 0.417,0.25 1.177,1.354 0.583,0.917 true 1.26,1.375 0.906,1.896 true 1.583,0.281 2.083,0.521 0.5,0.24 10 false H80 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,0.813 0.729,1.031 0.354,0.219 10 false V- 0.698,1.813 1.052,2.031 0.354,0.219 10 false V+
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C37
0.76,1.99 1.115,1.583 true 0.75,4.063 1.135,3.604 true 1.604,4.052 1.271,3.542 true 1.573,1.958 1.229,1.479 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.542,4.052 1.906,4.313 0.365,0.26 10 false *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal H80-28 (V+) - H80-29 (V-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.



Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)

Pre-procedure1

a.

Disconnect the O25 parking assist ECU connector.


b.

Disconnect the H80 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25,H80)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

O25-27 (NS+) - H80-28 (V+) Always Below 1 Ω
O25-28 (NS-) - H80-29 (V-) Always Below 1 Ω
O25-27 (NS+) - Body ground Always 10 kΩ or higher
O25-28 (NS-) - Body ground Always 10 kΩ or higher
O25-29 (NSG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.INSPECT PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PARKING ASSIST ECU

Pre-procedure1

a.
E366062C70
1.5,0.25 1.917,0.5 0.417,0.25 1.177,1.354 0.583,0.917 true 1.26,1.375 0.906,1.896 true 1.583,0.281 2.083,0.521 0.5,0.24 10 false H80 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,0.813 0.729,1.031 0.354,0.219 10 false V- 0.698,1.813 1.052,2.031 0.354,0.219 10 false V+
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C37
0.76,1.99 1.115,1.583 true 0.75,4.063 1.135,3.604 true 1.604,4.052 1.271,3.542 true 1.573,1.958 1.229,1.479 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.542,4.052 1.906,4.313 0.365,0.26 10 false *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Remove the radio and display receiver assembly with the connector still connected.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL



Procedure1

b.

Check the waveform of the parking assist ECU using an oscilloscope.

Item Content
Measurement terminal H80-28 (V+) - H80-29 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift position in R, camera lens is not covered, displaying an image.
Waveform 2: Ignition switch ON, shift position in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the parking assist ECU.

·

The video waveform is constantly output when the ignition switch is ACC.



OK:

Waveform is similar to that shown in the illustration.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG