Use the following procedure to troubleshoot the panoramic view monitor system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.
| Problem Symptom | Cause |
|---|---|
| The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. | The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the ignition switch off.
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/ Navigation System | A |
| w/ Audio and Visual System | B |
A
B
Refer to the navigation system.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Navigation system is normal | A |
| Navigation system is abnormal | B |
A
B
Refer to the audio and visual system.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PROBLEM SYMPTOMS TABLE
Audio and visual system is normal.
| Result | Proceed to |
|---|---|
| Audio and visual system is normal | A |
| Audio and visual system is abnormal | B |
A
B
Use the GTS to check if the CAN communication system is functioning normally.
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs and note any codes that are output.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs. Try to reproduce the problem symptoms based on the recorded DTCs, and then check if the DTCs are output again.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Refer to the Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Data List / Active Test
Terminals of ECU
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT