Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3700E _59 Vehicle Exterior _093706 DOOR / HATCH _0441751 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B222049  Back Door Motor Internal Electronic Failure  


DESCRIPTION

This DTC is stored when the multiplex network door ECU detects a malfunction of the motor built-into the power back door unit assembly set LH or power back door unit assembly set RH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B222049 Back Door Motor Internal Electronic Failure Malfunction of motor built into the power back door unit assembly set LH or power back door unit assembly set RH detected
·

Multiplex network door ECU

·

Power back door unit assembly set LH

·

Power back door unit assembly set RH

·

Harness or connector


Back Door A

WIRING DIAGRAM

E357346E23
4.26,3.021 4.719,3.219 0.458,0.198 10 false Y27 4.615,0.333 5.073,0.531 0.458,0.198 10 false BD+ 4.625,0.844 5.083,1.042 0.458,0.198 10 false BD- 2.031,0.406 2.49,0.604 0.458,0.198 10 false BD+ 2.052,0.906 2.51,1.104 0.458,0.198 10 false BD- 4.604,1.979 5.219,2.177 0.615,0.198 10 false BD+2 4.615,2.51 5.229,2.708 0.615,0.198 10 false BD-2 1.958,2.073 2.573,2.271 0.615,0.198 10 false BD+2 2,2.604 2.615,2.802 0.615,0.198 10 false BD-2 5.229,1.448 5.688,1.646 0.458,0.198 10 false CPU 0.896,1.323 1.354,1.521 0.458,0.198 10 false Y23 0.906,1.479 4.115,1.677 3.208,0.198 10 false Power Back Door Unit Assembly Set LH 0.906,3.01 1.365,3.208 0.458,0.198 10 false Y24 0.906,3.177 4.115,3.375 3.208,0.198 10 false Power Back Door Unit Assembly Set RH 4.26,3.188 6.99,3.448 2.729,0.26 10 false Multiplex Network Door ECU 2.406,0.313 2.563,0.51 0.156,0.198 10 false 1 2.406,1.979 2.563,2.177 0.156,0.198 10 false 1 2.417,0.833 2.573,1.031 0.156,0.198 10 false 2 2.417,2.5 2.573,2.698 0.156,0.198 10 false 2 4.427,0.323 4.583,0.521 0.156,0.198 10 false 1 4.427,1.979 4.583,2.177 0.156,0.198 10 false 6 4.438,2.49 4.594,2.688 0.156,0.198 10 false 8 4.438,0.833 4.594,1.031 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
50002 489

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 489

Result:
Result Proceed to
B222049 is output A
B222049 is not output B



A

3.INSPECT POWER BACK DOOR UNIT ASSEMBLY SET LH

B

3.INSPECT POWER BACK DOOR UNIT ASSEMBLY SET LH

Pre-procedure1

a.

Fully open the back door.


b.
E357428C12
1.469,0.073 1.885,0.323 0.417,0.25 1.938,0.75 2.25,0.51 true 1.479,0.74 1.146,0.573 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 0.802,0.448 1.115,0.604 0.313,0.156 10 false BD+ 2.323,0.427 2.635,0.583 0.313,0.156 10 false BD- 1.552,0.115 1.896,0.302 0.344,0.188 10 false Y23
*a Component without harness connected
(Power Back Door Unit Assembly Set LH)


Disconnect the power back door unit assembly set LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y23)Location & Routing

Click Connector(Y23)Body>No. 2 Back Door Wire>Power Back Door Unit Assembly Set LH

Y23-1 (BD+) - Body ground Always 10 kΩ or higher
Y23-2 (BD-) - Body ground Always 10 kΩ or higher
Y23-1 (BD+) - Y23-2 (BD-) Always Below 1 MΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT POWER BACK DOOR UNIT ASSEMBLY SET RH

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY SET LH

4.INSPECT POWER BACK DOOR UNIT ASSEMBLY SET RH

Pre-procedure1

a.

Fully open the back door.


b.
E357428C13
1.469,0.083 1.875,0.344 0.406,0.26 1.938,0.75 2.25,0.51 true 1.479,0.74 1.146,0.573 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 0.76,0.458 1.25,0.656 0.49,0.198 10 false BD+2 2.323,0.427 2.688,0.625 0.365,0.198 10 false BD-2 1.542,0.125 1.906,0.323 0.365,0.198 10 false Y24
*a Component without harness connected
(Power Back Door Unit Assembly Set RH)


Disconnect the power back door unit assembly set RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y24)Location & Routing

Click Connector(Y24)Body>No. 2 Back Door Wire>Power Back Door Unit Assembly Set RH

Y24-1 (BD+2) - Body ground Always 10 kΩ or higher
Y24-2 (BD-2) - Body ground Always 10 kΩ or higher
Y24-1 (BD+2) - Y24-2 (BD-2) Always Below 1 MΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY SET RH

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)

Pre-procedure1

a.

Disconnect the Y27 multiplex network door ECU connector.


b.

Disconnect the Y23 power back door unit assembly set LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y27,Y23)Location & Routing

Click Connector(Y27)Body>No. 2 Back Door Wire>Multiplex Network Door ECU

Click Connector(Y23)Body>No. 2 Back Door Wire>Power Back Door Unit Assembly Set LH

Y27-1 (BD+) - Y23-1 (BD+) Always Below 1 Ω
Y27-3 (BD-) - Y23-2 (BD-) Always Below 1 Ω
Y27-1 (BD+) or Y23-1 (BD+) - Body ground Always 10 kΩ or higher
Y27-3 (BD-) or Y23-2 (BD-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET RH)

Pre-procedure1

a.

Disconnect the Y27 multiplex network door ECU connector.


b.

Disconnect the Y24 power back door unit assembly set RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y27,Y24)Location & Routing

Click Connector(Y27)Body>No. 2 Back Door Wire>Multiplex Network Door ECU

Click Connector(Y24)Body>No. 2 Back Door Wire>Power Back Door Unit Assembly Set RH

Y27-6 (BD+2) - Y24-1 (BD+2) Always Below 1 Ω
Y27-8 (BD-2) - Y24-2 (BD-2) Always Below 1 Ω
Y27-6 (BD+2) or Y24-1 (BD+2) - Body ground Always 10 kΩ or higher
Y27-8 (BD-2) or Y24-2 (BD-2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR