Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR DRIVE UNIT
RM3700E _59 Vehicle Exterior _093706 DOOR / HATCH _0444895 POWER BACK DOOR DRIVE UNIT A

DOOR / HATCH  POWER BACK DOOR DRIVE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B599213N01
6.385,0.792 6.604,0.792 false 5.115,0.594 5.448,0.594 false 6.01,1.917 6.344,1.917 false 2.167,2.844 2.5,2.844 false 0.781,2.531 0.99,2.531 false 5.896,2.385 5.896,2.719 false 1.969,3.167 2.302,3.167 false 1.021,1.833 1.354,1.833 false 2.292,0.667 2.625,0.667 false 1.698,1.594 1.802,1.385 1.802,1.385 1.969,1.385 false 5.813,0.417 5.813,0.802 false 2.719,0.479 3,0.833 0.281,0.354 18 false 1 6.885,0.635 7.135,0.979 0.25,0.344 18 false 2 4.917,0.438 5.198,0.792 0.281,0.354 18 false 3 6.427,1.74 6.708,2.094 0.281,0.354 18 false 4 5.844,2.75 6.125,3.104 0.281,0.354 18 false 5 1.271,2.406 1.521,2.75 0.25,0.344 18 false 2 0.802,1.677 1.083,2.031 0.281,0.354 18 false 3 2.563,2.677 2.844,3.031 0.281,0.354 18 false 4 2.375,3 2.656,3.354 0.281,0.354 18 false 5 2,1.281 2.833,1.615 0.833,0.333 10 false ● ★ 1.719,1.656 2.552,1.99 0.833,0.333 10 false x2 1.573,3.042 2.406,3.375 0.833,0.333 10 false x2 5.698,0.833 6.531,1.167 0.833,0.333 10 false ● ★ 5.885,0.292 6.719,0.625 0.833,0.333 10 false x2 6.438,2.271 6.885,2.583 0.448,0.313 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BACK DOOR TRIM BOARD 67751 - - -
2 POWER BACK DOOR UNIT SET ASSEMBLY 68920 (Click here) - -
3 BACK DOOR UPPER DAMPER STAY BRACKET 68946 - - -
4 BACK DOOR LOWER DAMPER STAY BRACKET 68948 - - -
5 BACK DOOR STAY STOPPER 68984 - - -

● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.



PROCEDURE

Hide 67751 1.REMOVE BACK DOOR TRIM BOARD

Hide 68920 2.REMOVE POWER BACK DOOR UNIT SET ASSEMBLY

CAUTION:
·

Do not perform work if the back door is not securely supported.

·

The back door could fall, resulting in injury.


B594650


NOTICE:
·

Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.

·

Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.

·

Do not apply any horizontal load to the door stay in order to prevent the piston rod from deforming.



a.
B594651C03
2.958,0.031 3.24,0.344 0.281,0.313 18 false ii 4.344,1.271 4.5,1.552 0.156,0.281 18 true i
V100135

Grease
V100136

Connector
V113147

Remove in this Direction - -


i.

Disconnect the connector.


ii.

Disconnect the grommet and pull out the power back door unit assembly LH harness as shown in the illustration.



b.
B599214C01
0.448,0.073 1.823,0.427 1.375,0.354 18 false i, ii
V100155

Protective Tape - -


i.

Using a screwdriver with its tip wrapped with protective tape, slightly raise the 2 stop rings as shown in the illustration.


ii.

Disengage the 2 ball joints to remove the power back door unit assembly.

NOTICE:
·

Remove the power back door unit assembly LH while supporting the back door by hand.

·

Remove the back door stay assembly while supporting the back door stay assembly by hand.





Hide 68946 3.REMOVE BACK DOOR UPPER DAMPER STAY BRACKET

a.
B594653N01
0.135,0.125 0.417,0.479 0.281,0.354 18 false i

i.

Remove the 2 bolts and back door upper damper stay bracket.



Hide 68948 4.REMOVE BACK DOOR LOWER DAMPER STAY BRACKET

a.
B594654N01
0.156,0.073 0.438,0.427 0.281,0.354 18 false i

i.

Remove the 2 bolts and back door lower damper stay bracket LH with back door stay stopper.



Hide 68984 5.REMOVE BACK DOOR STAY STOPPER

a.
B594655N01
0.135,0.083 0.417,0.438 0.281,0.354 18 false i

i.

Disengage the claw and remove the back door stay stopper from the back door lower damper stay bracket.