When the power back door warning system does not operate, one of the following may be malfunctioning: 1) wireless door lock control system, 2) power back door warning buzzer circuit or 3) multiplex network door ECU.
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
The power back door warning function can be customized. Make sure the function is ON.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Check power back door system operation.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Hazard warning light does not come on | A |
| Power back door warning buzzer does not operate | B |
A
B
Check wireless door lock operation.
w/ Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING
w/o Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING
Hazard answer-back function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING
w/o Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING
Temporarily replace the multiplex network door ECU with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the initialization for the multiplex network door ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check that the power back door hazard warning lights operate normally.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK
The power back door hazard warning lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PBD Buzzer (Small Volume) | Power back door warning buzzer sound (small volume) | Start | - |
| PBD Buzzer (Middle Volume) | Power back door warning buzzer sound (Middle volume) | Start | - |
| PBD Buzzer (Large Volume) | Power back door warning buzzer sound (Large volume) | Start | - |
| Tester Display |
|---|
| PBD Buzzer (Small Volume) |
| Tester Display |
|---|
| PBD Buzzer (Middle Volume) |
| Tester Display |
|---|
| PBD Buzzer (Large Volume) |
Power back door warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y31 power back door warning buzzer connector.
Disconnect the Y30 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y31,Y30)Location & Routingewd_type=routing;type=c,c;code=Y31,Y30 Click Connector(Y31)Body>No. 2 Back Door Wire>Power Back Door Warning Buzzerewd_type=component;type=c;code=Y31;pinno=1,2 Click Connector(Y30)Body>No. 2 Back Door Wire>Multiplex Network Door ECUewd_type=component;type=c;code=Y30;pinno=1 |
||
| Y31-1 (BZR+) - Y30-1 (BZR+) | Always | Below 1 Ω |
| Y31-2 (BZR-) - Body ground | Always | Below 1 Ω |
| Y31-1 (BZR+) or Y30-1 (BZR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the power back door warning buzzer with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR WARNING BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that the power back door warning buzzer operates normally.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK
Power back door warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG