Home › Suspension › REAR SUSPENSION › REAR LOWER ARM › 2020.08–2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441859 REAR LOWER ARM A

REAR SUSPENSION  REAR LOWER ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444398N02
4.375,3.938 4.813,3.938 false 2.135,1.479 2.604,1.479 false 1.708,1.885 1.708,2.469 false 0.823,2.24 0.823,2.51 false 0.771,2.521 1.052,2.875 0.281,0.354 18 false 3 1.781,2.438 2.063,2.792 0.281,0.354 18 false 4 2.917,1.323 3.198,1.677 0.281,0.354 18 false 2 4.156,3.781 4.438,4.135 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR WHEEL - - - -
2 REAR NO. 2 SUSPENSION TOE ADJUST PLATE 48452R (Click here) - -
3 CAMBER ADJUST CAM SUB-ASSEMBLY - - - -
4 LOWER CONTROL ARM ASSEMBLY 48730 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during lower control arm assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Rear wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 48452R 2.REMOVE REAR NO. 2 SUSPENSION TOE ADJUST PLATE

a.
C443659C01
1.781,0.635 1.844,0.917 1.844,0.917 1.885,0.646 true 0.833,1.323 0.896,1.604 0.896,1.604 0.938,1.333 true 0.885,0.063 1.083,0.323 0.198,0.26 18 true i 4.198,0.073 4.385,0.344 0.188,0.271 18 true ii 1.781,0.958 2.031,1.125 0.25,0.167 10 true *a 0.823,1.615 1.073,1.781 0.25,0.167 10 true *a
*a Matchmarks - -


i.

Place matchmarks on the rear No. 2 suspension toe adjust plate, camber adjust cam sub-assembly and rear suspension member sub-assembly.


ii.

Loosen the nut.

NOTICE:

Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.




Hide 3.REMOVE CAMBER ADJUST CAM SUB-ASSEMBLY

a.
C443660


Hide 48730 4.REMOVE LOWER CONTROL ARM ASSEMBLY

a.
C443661N01
2.531,0.052 2.719,0.323 0.188,0.271 18 true i

i.

Remove the bolt, nut and lower control arm assembly from the rear No. 1 suspension arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.