| *A | for HV Model | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.
When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC [C13CD00, C13CE00, C140000] may be stored. As there is no malfunction, clear the DTC. (for HV Model)
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
04946
1.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT
|
|
| *1 | Rear No. 1 Disc Brake Anti-squeal Shim | *2 | Rear No. 2 Disc Brake Anti-squeal Shim |
| *3 | Rear Disc Brake Pad Wear Indicator Plate | - | - |
| *a | Inner Side (Pink) | *b | Outer Side (Light Blue) |
Check the rear disc brake pad has an identification mark, be sure to confirm the installation location.
Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad.
Install a new rear disc brake pad wear indicator plate to each rear disc brake pad.
04466
2.INSTALL REAR DISC BRAKE PAD
|
|
| *1 | Rear No. 1 Disc Brake Anti-squeal Shim | *2 | Rear No. 2 Disc Brake Anti-squeal Shim |
| *3 | Rear Disc Brake Pad Wear Indicator Plate | - | - |
| *a | Inner Side (Pink) | *b | Outer Side (Light Blue) |
Check the rear disc brake pad has an identification mark, be sure to confirm the installation location.
Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.
Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.
47850
3.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
Using SST, push back the front disc brake piston.
Make sure the brake fluid does not overflow from the reservoir.
Do not forcibly push in the rear disc brake piston.
Hold the front disc brake cylinder slide pin (lower side) and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the bolt.
6.INSPECT BRAKE FLUID LEVEL IN RESERVOIR
for HV Model: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>ON-VEHICLE INSPECTION
for Gasoline Model: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>ON-VEHICLE INSPECTION
7.INSTALL REAR WHEEL
8. NORMAL CONDITION RECOVERY
for HV Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model)>UTILITY
for Gasoline Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model)>TEST MODE PROCEDURE
9. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model)
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART