Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL SOLENOID (for Intake Side)
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442017 CAMSHAFT OIL CONTROL SOLENOID(for Intake Side) A

M15A-FKS ENGINE CONTROL  CAMSHAFT OIL CONTROL SOLENOID(for Intake Side)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A479402N01
2.365,3.031 3.031,3.198 0.667,0.167 1.75,4.406 2.417,4.573 0.667,0.167 2.906,2.521 2.479,2.188 2.479,2.188 2.313,2.188 false 2.052,3.927 2.385,3.927 false 1.292,4.365 1.583,4.5 1.583,4.5 1.75,4.5 false 0.385,0.271 0.719,0.271 false 2.688,3.021 2.688,2.938 2.688,2.938 2.646,2.813 false 0.781,0.146 1.063,0.5 0.281,0.354 18 false 3 2.104,2.073 2.385,2.427 0.281,0.354 18 false 1 2.698,2.729 2.979,3.083 0.281,0.354 10 false x2 1.24,4.417 1.521,4.771 0.281,0.354 10 false x2 2.427,3.042 3.104,3.25 0.677,0.208 8 false 10 (102, 7) 2.458,3.781 2.74,4.135 0.281,0.354 18 false 2 2.083,3.021 2.51,3.375 0.427,0.354 10 false ●★ 1.813,4.417 2.49,4.625 0.677,0.208 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY 15370 (Click here) - -
2 ENGINE WIRE - - - -
3 INSPECT FOR ENGINE OIL LEAK - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
★ Precoated part - -

PROCEDURE

Hide 15370 1.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY

Z101186

HINT:

Perform this procedure only when replacement of the O-ring is necessary.



a.
A458773N02
0.979,0.146 1.792,0.448 0.813,0.302 18 false i, ii, iii 4.521,0.146 5.052,0.417 0.531,0.271 18 true iv, v

i.

Clean the O-ring groove of the cam timing oil control solenoid assembly.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



ii.

Install a new O-ring to the cam timing oil control solenoid assembly.

NOTICE:

Do not damage the O-ring when installing it.



iii.

Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration.

NOTICE:

Do not damage the O-ring.



iv.

Using an 8 mm socket wrench, install the cam timing oil control solenoid assembly to the No. 2 timing chain cover assembly with 2 new bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control solenoid assembly .




v.

Connect the camshaft timing oil control solenoid assembly connector.



Hide 2.DISCONNECT ENGINE WIRE

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 3.INSPECT FOR ENGINE OIL LEAK