Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › CAMSHAFT POSITION SENSOR
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442023 CAMSHAFT POSITION SENSOR A

M15A-FKS ENGINE CONTROL  CAMSHAFT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A460406N01
6.063,0.615 6.563,0.781 0.5,0.167 4.583,0.344 5.083,0.51 0.5,0.167 4.542,0.302 5.125,0.552 0.583,0.25 6.021,0.573 6.604,0.823 0.583,0.25 5.219,1.656 5.375,1.948 5.375,1.948 5.542,1.948 false 6.417,0.333 6.75,0.333 false 5.333,0.708 5.667,0.708 false 3.854,0.625 4,0.458 4,0.458 4.167,0.458 false 2.708,1.292 3.542,1.292 false 5.313,1.344 6.01,1.344 false 3.135,1.573 3.5,1.573 false 6.438,1.219 6.719,1.573 0.281,0.354 18 false 1 2.49,1.156 2.771,1.51 0.281,0.354 18 false 2 6.24,0.188 6.521,0.542 0.281,0.354 18 false 3 5.729,0.646 6.073,0.854 0.344,0.208 10 false ●★ 6.135,0.646 6.729,0.792 0.594,0.146 8 false 7.5 (76) 4.229,0.365 4.573,0.573 0.344,0.208 10 false ●★ 4.667,0.375 5.26,0.521 0.594,0.146 8 false 7.5 (76) 5.615,1.896 5.958,2.104 0.344,0.208 10 false ● 2.948,1.521 3.292,1.729 0.344,0.208 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAMSHAFT POSITION SENSOR (for Exhaust Side) 11102A (Click here) - -
2 CAMSHAFT POSITION SENSOR (for Intake Side) 11102A (Click here) - -
3 INSPECT FOR ENGINE OIL LEAK - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
★ Precoated part - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11102A 1.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)

a.
A458048N01
0.938,0.167 1.563,0.469 0.625,0.302 18 false i, ii, iii 4.51,0.156 5.031,0.458 0.521,0.302 18 true iv, v

i.

Clean the O-ring groove of the camshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



ii.

Install a new O-ring to the camshaft position sensor.

NOTICE:

Set the O-ring on the tip of the camshaft position sensor and roll it into the O-ring groove with bare hands to install it.



iii.

Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



iv.

Using an 8 mm socket wrench, install the camshaft position sensor to the cylinder head cover sub-assembly with a new bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·

If the camshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.





Hide 11102A 2.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)

a.
A458047N01
0.927,0.177 1.594,0.469 0.667,0.292 18 false i, ii, iii 4.542,0.146 5.042,0.438 0.5,0.292 18 true iv, v

i.

Clean the O-ring groove of the camshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



ii.

Install a new O-ring to the camshaft position sensor.

NOTICE:

Set the O-ring on the tip of the camshaft position sensor and roll it into the O-ring groove with bare hands to install it.



iii.

Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



iv.

Using an 8 mm socket wrench, install the camshaft position sensor to the cylinder head cover sub-assembly with a new bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·

If the camshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.




v.

Connect the camshaft position sensor connector.



Hide 3.INSPECT FOR ENGINE OIL LEAK