Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › CAMSHAFT OIL CONTROL SOLENOID
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442033 CAMSHAFT OIL CONTROL SOLENOID A

M15A-FXE ENGINE CONTROL  CAMSHAFT OIL CONTROL SOLENOID  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A460395N02
1.865,2.146 2.448,2.313 0.583,0.167 0.615,4.396 1.198,4.563 0.583,0.167 3.25,3.021 3.333,3.021 3.333,3.021 3.365,2.542 false 0.333,0.25 0.667,0.25 false 1.313,3.333 1.646,3.333 false 2.448,2.229 2.615,2.229 2.615,2.229 2.76,2.563 false 1.198,4.479 1.531,4.479 false 0.792,0.104 1.073,0.458 0.281,0.354 18 false 3 3.115,2.865 3.396,3.219 0.281,0.354 18 false 1 1.094,3.188 1.375,3.542 0.281,0.354 18 false 2 1.875,2.156 2.531,2.333 0.656,0.177 8 false 10 (102, 7) 2.823,2.594 3.271,2.771 0.448,0.177 10 false x2 1.677,4.427 2.125,4.604 0.448,0.177 10 false x2 1.563,2.156 2.01,2.333 0.448,0.177 10 false ●★ 0.625,4.406 1.281,4.583 0.656,0.177 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAM TIMING OIL CONTROL SOLENOID ASSEMBLY 15370 (Click here) - -
2 ENGINE WIRE - - - -
3 INSPECT FOR ENGINE OIL LEAK - - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
★ Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 15370 1.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Z101186

HINT:

Perform this procedure only when replacement of the O-ring is necessary.



a.
A458745N02
1.01,0.167 1.76,0.49 0.75,0.323 18 false i, ii, iii 4.552,0.156 5.01,0.438 0.458,0.281 18 true iv, v

i.

Clean the O-ring groove of the cam timing oil control solenoid assembly.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



ii.

Install a O-ring to the cam timing oil control solenoid assembly.

NOTICE:

Do not damage the O-ring when installing it.



iii.

Apply a light coat of engine oil to the O-ring of the cam timing oil control solenoid assembly.

NOTICE:

If reusing the cam timing oil control solenoid assembly, be sure to inspect the O-ring.



iv.

Using an 8 mm socket wrench, install the cam timing oil control solenoid assembly to the No. 2 timing chain cover assembly with 2 new bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the cam timing oil control solenoid assembly has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the cam timing oil control solenoid assembly.




v.

Connect the cam timing oil control solenoid assembly connector.



Hide 2.INSTALL ENGINE WIRE

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 3.INSPECT FOR ENGINE OIL LEAK