Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › CAMSHAFT TIMING CONTROL MOTOR
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442034 CAMSHAFT TIMING CONTROL MOTOR A

M15A-FXE ENGINE CONTROL  CAMSHAFT TIMING CONTROL MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A460396N01
0.333,4.5 0.833,4.667 0.5,0.167 1.521,2.396 2.021,2.563 0.5,0.167 3.094,3.094 3.021,3.448 3.021,3.448 2.854,3.448 false 0.938,3.448 1.271,3.448 false 0.438,0.333 0.771,0.333 false 0.365,0.729 0.698,0.729 false 0.833,4.615 1.167,4.615 false 2.021,2.479 2.188,2.479 2.188,2.479 2.354,2.729 false 3.01,1.979 3.177,1.979 3.177,1.979 3.344,2.229 false 0.458,1.167 0.792,1.167 false 0.865,0.208 1.146,0.563 0.281,0.354 18 false 3 0.771,0.594 1.5,0.896 0.729,0.302 18 false 4 2.688,3.323 2.969,3.677 0.281,0.354 18 false 1 0.74,3.302 1.021,3.656 0.281,0.354 18 false 2 2.823,1.917 3.073,2.156 0.25,0.24 10 false ● 0.375,4.531 0.948,4.667 0.573,0.135 8 false 10 (102) 1.563,2.427 2.135,2.563 0.573,0.135 8 false 21 (214) 2.427,2.75 2.74,2.948 0.313,0.198 10 false x3 1.313,4.563 1.625,4.76 0.313,0.198 10 false x2 0.865,1.031 1.521,1.406 0.656,0.375 18 false 5, 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY 13090E (Click here) - -
2 ENGINE WIRE - - - -
3 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - (Click here) - -
5 INSPECT FOR ENGINE OIL LEAK - - - (Click here)
6 PERFORM INITIALIZATION - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

PROCEDURE

Hide 13090E 1.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

a.
A458747N01
0.396,0.156 0.677,0.51 0.281,0.354 18 false i 4.354,0.156 4.635,0.51 0.281,0.354 18 false ii 2.438,2.781 3.24,3.094 0.802,0.313 18 true iii, iv, v 3.021,3.094 3.219,3.281 0.198,0.188 10 true 3 4.49,3.604 4.688,3.792 0.198,0.188 10 true 2 3.698,4.313 3.896,4.5 0.198,0.188 10 true 1

i.

Install a new cam timing control motor O-ring to the No. 2 timing chain cover assembly with the protrusion of the cam timing control motor O-ring oriented as shown in the illustration.


ii.

Turn the cutout of the camshaft timing gear assembly eccentric shaft counterclockwise by hand, and set it to the maximum retard angle position.

HINT:
·

If a camshaft lobe is opening a valve, the eccentric shaft will be difficult to turn.

·

When the cutout of the camshaft timing gear assembly eccentric shaft cannot be turned any farther, it is set to the maximum retard angle.




iii.

Install the cam timing control motor with EDU assembly to the No. 2 timing chain cover assembly.

NOTICE:
A458748C02
0.906,1.229 0.5,0.417 0.5,0.417 1.083,1.135 true 1.375,0.875 1.281,1.885 1.281,1.885 0.448,1.427 true 2.021,0.844 1.906,1.854 1.906,1.854 3.021,1.573 true 2.75,1.26 2.99,0.521 2.99,0.521 2.583,1.042 true 0.313,0.271 0.625,0.469 0.313,0.198 10 false *a 1.281,1.896 1.594,2.094 0.313,0.198 10 false *c 1.708,1.896 2.021,2.094 0.313,0.198 10 true *d 3.031,0.396 3.344,0.594 0.313,0.198 10 true *b
*a Joint
*b Cutout
*c Pin Hole
*d Knock Pin


·

When installing, align the joints of the cam timing control motor with EDU assembly with the cutouts of the camshaft timing gear assembly eccentric shaft.

·

Align the pin holes of the cam timing control motor with EDU assembly with the knock pins of the No. 2 timing chain cover assembly when installing the cam timing control motor with EDU assembly.

·

Make sure the contact surface of the cam timing control motor with EDU assembly (the surface that contacts the No. 2 timing chain cover assembly) is free of foreign matter.

·

When installing the cam timing control motor with EDU assembly, do not use excessive force.

·

If the cam timing control motor with EDU assembly has been struck or dropped, replace it.

·

Do not disassemble the cam timing control motor with EDU assembly. If disassembled, replace it.




iv.

Install the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


v.

Connect the cam timing control motor with EDU assembly connector.



Hide 2.INSTALL ENGINE WIRE

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 5.INSPECT FOR ENGINE OIL LEAK

Hide 6.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after removing and installing, or replacing the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION