|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP grease |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
1.INSTALL RADIATOR DRAIN COCK PLUG
|
|
16535
2.INSTALL LOWER RADIATOR SUPPORT
16523A
3.INSTALL RADIATOR SUPPORT CUSHION
16400
4.INSTALL RADIATOR ASSEMBLY
|
|
884A0
5.INSTALL COOLER CONDENSER ASSEMBLY
|
|
16572D
6.CONNECT NO. 2 RADIATOR HOSE
16573B
7.CONNECT NO. 3 RADIATOR HOSE
16502
8.INSTALL WATER FILLER SUB-ASSEMBLY
9.CONNECT RADIATOR RESERVOIR TANK HOSE
16261G
10.CONNECT NO. 1 WATER BY-PASS HOSE
16595D
11.INSTALL NO. 1 RADIATOR AIR GUIDE LH
16561D
12.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
16562L
13.INSTALL NO. 2 RADIATOR TO SUPPORT SEAL
16695A
14.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH
16691A
15.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH
53213C
16.INSTALL UPPER FRONT RADIATOR SUPPORT
| *A | When Reusing Upper Front Radiator Support | - | - |
When replacing upper front radiator support:
1. Align the upper front radiator support according to the reference values and point-to-point distances, and temporarily install it with the 4 bolts.
for Reference Values:
Body Repair Manual > Vehicle Exterior > BODY PANEL > RADIATOR SUPPORT> REFERENCE VALUE
for Point-to-point Distances:
Body Repair Manual > Vehicle Exterior > BODY DIMENSIONS > ENGINE COMPARTMENT REFERENCE VALUES > POINT-TO-POINT DISTANCE
When reusing upper front radiator support:
1. Align the upper front radiator support with the matchmark positions and temporarily install it with the 4 bolts as shown in the illustration.
When reusing upper front radiator support:
Align the upper front radiator support with the matchmark positions and temporarily install it with the 4 bolts as shown in the illustration.
Tighten the 4 bolts.
17.CONNECT WIRE HARNESS
Connect the connector.
Connect the wire harness with the bolt.
Engage the clamp and connect the wire harness.
Engage the 2 clamps and connect the wire harness.
Connect the 2 airbag connectors.
When connecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
53630
18.CONNECT HOOD LOCK CONTROL CABLE ASSEMBLY
17701
19.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
52131A
21.INSTALL FRONT BUMPER REINFORCEMENT
52611
22.INSTALL FRONT BUMPER ENERGY ABSORBER
16681A
23.INSTALL RADIATOR UPPER AIR GUIDE PLATE
24.INSTALL HEADLIGHT ASSEMBLY LH
for Halogen Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>INSTALLATION
for LED Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>INSTALLATION
25.INSTALL HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
26.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
27.ADD ENGINE COOLANT
28.INSPECT FOR COOLANT LEAK
51410
29.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
30.INSPECT SRS WARNING LIGHT
53301
31.INSPECT HOOD SUB-ASSEMBLY
53510
32.ADJUST HOOD LOCK ASSEMBLY
33. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART