The smart door control receiver assembly is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the smart door control receiver assembly. The smart door control receiver assembly receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B124296 | Wireless Door Lock Tuner Component Internal Failure | ·
Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and smart door control receiver assembly. ·
Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO |
·
Wire harness or connector ·
Smart door control receiver assembly ·
Certification ECU (smart key ECU assembly) |
Entry&Start | A |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
When replacing or inspecting the smart door control receiver assembly and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the smart door control receiver assembly, the performance of the entry function and wireless function may be affected.
This DTC is not stored within 10 seconds of the ignition switch being turned from on to off.
Make sure that there are no electrical key transmitter sub-assemblies in the vehicle.
Pre-procedure1
Disconnect the O48 smart door control receiver assembly connector.
Procedure1
Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H46)Location & Routingewd_type=routing;type=c;code=H46 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=29 |
||
| H46-29 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O47,H46)Location & Routingewd_type=routing;type=c,c;code=O47,H46 Click Connector(O47)Instrument Panel>Floor Wire>Certification ECUewd_type=component;type=c;code=O47;pinno=11,21 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=29 |
||
| O47-11 (RDAM) - H46-29 (E) | Always | 11 to 14 V |
| O47-21 (RCO) - H46-29 (E) | Always | Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the O47 certification ECU (smart key ECU assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O47,O48)Location & Routingewd_type=routing;type=c,c;code=O47,O48 Click Connector(O47)Instrument Panel>Floor Wire>Certification ECUewd_type=component;type=c;code=O47;pinno=11,21 Click Connector(O48)Body>Floor Wire>Smart Door Control Receiver Assemblyewd_type=component;type=c;code=O48;pinno=5,4,1 |
||
| O47-11 (RDAM) - O48-5 (DATA) | Always | Below 1 Ω |
| O47-21 (RCO) - O48-4 (+5) | Always | Below 1 Ω |
| O48-1 (GND) - Body ground | Always | Below 1 Ω |
| O48-5 (DATA) or O47-11 (RDAM) - Other terminals and body ground | Always | 10 kΩ or higher |
| O48-4 (+5) or O47-21 (RCO) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG