Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function, Gasoline Model) › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093748 THEFT DETERRENT / KEYLESS ENTRY _0441965 ENTRY AND START SYSTEM(for Entry Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function, Gasoline Model)  Entry Exterior Alarm and Answer-back Buzzer do not Sound  


DESCRIPTION

The entry and start system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via CAN communication and the buzzer sounds.

WIRING DIAGRAM

B506724E09
0.635,3.25 2.438,3.521 1.802,0.271 10 false : CAN Communication Line 3.552,2.698 5.208,3.281 1.656,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 2.458,1.75 3.906,2.229 1.448,0.479 10 false Power Distribution Box Assembly 2.469,1.573 2.906,1.875 0.438,0.302 10 false 4D 5.542,2.667 7.052,3.177 1.51,0.51 10 false Certification ECU (Smart Key ECU Assembly) 0.406,1.625 1.667,2.167 1.26,0.542 10 false Wireless Door Lock Buzzer 3.552,2.542 3.99,2.844 0.438,0.302 10 false MB 0.406,1.469 0.844,1.771 0.438,0.302 10 false A57 2.458,0.938 2.896,1.24 0.438,0.302 10 false 7 1.729,0.938 2.167,1.24 0.438,0.302 10 false 1 0.51,0.938 0.948,1.24 0.438,0.302 10 false 2 3.76,0.927 4.198,1.229 0.438,0.302 10 false 3 0.677,0.938 1.115,1.24 0.438,0.302 10 false E 1.531,0.938 1.969,1.24 0.438,0.302 10 false B 3.958,0.938 4.396,1.24 0.438,0.302 10 false BZR 4.25,0.531 4.688,0.833 0.438,0.302 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Wireless Door Lock Buzzer Answer-back Function A
w/o Wireless Door Lock Buzzer Answer-back Function B



A

2.CHECK CUSTOMIZE SETTING (WIRELESS BUZZER RESPONSE FUNCTION)

B

6.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
2.CHECK CUSTOMIZE SETTING (WIRELESS BUZZER RESPONSE FUNCTION)
a.

Check customize setting.

Wireless Door Lock
Tester Display Description Default Setting ECU
Wireless Buzzer Response Function Wireless buzzer response Enable $00:Disable,$01:Enable Main body ECU (multiplex network body ECU)
50006 1

Result:
Result Proceed to
"Enable" is displayed A
"Disable" is displayed B



A

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

B

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

4.READ VALUE USING GTS (DOOR LOCK POSITION SWITCH STATUS)

B

4.READ VALUE USING GTS (DOOR LOCK POSITION SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Position Switch Status Front door RH unlock detection switch signal Lock or Unlock Lock: Front door RH locked
Unlock: Front door RH unlocked
-
FL Door Lock Position Switch Status Front door LH unlock detection switch signal Lock or Unlock Lock: Front door LH locked
Unlock: Front door LH unlocked
-
RR Door Lock Position Switch Status Rear door RH unlock detection switch signal Lock or Unlock Lock: Rear door RH locked
Unlock: Rear door RH unlocked
-
RL Door Lock Position Switch Status Rear door LH unlock detection switch signal Lock or Unlock Lock: Rear door LH locked
Unlock: Rear door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Position Switch Status
FL Door Lock Position Switch Status
RR Door Lock Position Switch Status
RL Door Lock Position Switch Status
50003 449 20,21,22,23
OK:

The GTS display changes correctly in response to the lock/unlock operation.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Perform Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 449 31

Result:
Result Proceed to
Wireless door lock buzzer does not sound A
Wireless door lock buzzer sounds B



A

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (NO ANSWER-BACK)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Perform Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 449 31
OK:

Wireless door lock buzzer sounds



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
7.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Disconnect the A57 wireless door lock buzzer connector.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 449 31

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A57)Location & Routing

Click Connector(A57)Engine Compartment>Engine Room Main Wire>Wireless Door Lock Buzzer

A57-1 (B) - A57-2 (E) Active Test Wireless Buzzer is OFF Below 1 V
Active Test Wireless Buzzer is ON Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)



Result:
Proceed to
OK
NG



OK

REPLACE WIRELESS DOOR LOCK BUZZER

NG

8.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
8.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A57)Location & Routing

Click Connector(A57)Engine Compartment>Engine Room Main Wire>Wireless Door Lock Buzzer

A57-1 (B) - MB-3 (BZR) Always Below 1 Ω
A57-2 (E) - Body ground Always Below 1 Ω
A57-1 (B) or MB-3 (BZR) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

9.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - POWER DISTRIBUTION BOX ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4D power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A57)Location & Routing

Click Connector(A57)Engine Compartment>Engine Room Main Wire>Wireless Door Lock Buzzer

A57-1 (B) - 4D-7 Always Below 1 Ω
A57-1 (B) or 4D-7 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR