Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093748 THEFT DETERRENT / KEYLESS ENTRY _0441966 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  System Malfunction Message is Displayed on the Multi-information Display  


SYSTEM DESCRIPTION

If an abnormal operation that may lead to a malfunction of the steering lock ECU (steering lock actuator or upper bracket assembly), or abnormal vehicle speed information is detected by the certification ECU (smart key ECU assembly), a system malfunction message is displayed on the multi-information display.

WIRING DIAGRAM

B587329E05
5.531,4.677 7.073,5.177 1.542,0.5 10 false Certification ECU (Smart Key ECU Assembly) 0.052,2.313 2.885,2.865 2.833,0.552 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 0.073,2.167 0.875,2.438 0.802,0.271 10 false H71 1.771,0.656 2.573,0.927 0.802,0.271 10 false B 1.969,0.552 2.771,0.823 0.802,0.271 10 false 7 3.354,0.646 5.115,1.042 1.76,0.396 10 false from Auxiliary Battery 2.125,0.823 3.188,1.177 1.063,0.354 10 false STRG LOCK 1.646,1.198 2.448,1.469 0.802,0.271 10 false IGE 1.969,1.094 2.771,1.365 0.802,0.271 10 false 3 1.573,1.698 2.375,1.969 0.802,0.271 10 false GND 1.969,1.594 2.771,1.865 0.802,0.271 10 false 1 5.896,1.208 6.698,1.479 0.802,0.271 10 false SLR+ 5.896,1.688 6.698,1.958 0.802,0.271 10 false E 5.615,1.031 6.417,1.302 0.802,0.271 10 false 24 5.615,1.531 6.417,1.802 0.802,0.271 10 false 29 6.552,3.854 6.729,4.135 0.177,0.281 10 false IC 6.229,3.146 6.49,3.458 0.26,0.313 10 false +B 5.885,3.542 6.688,3.813 0.802,0.271 10 false ST2 5.635,3.469 6.438,3.74 0.802,0.271 10 false 2 0.135,4.802 2.25,5.146 2.115,0.344 10 false Hybrid Vehicle Control ECU 0.969,3.542 1.771,3.813 0.802,0.271 10 false ST2 1.333,3.542 2.135,3.813 0.802,0.271 10 false 4 0.146,4.646 0.948,4.917 0.802,0.271 10 false H44 5.563,1.219 6.365,1.49 0.802,0.271 10 false H46 5.563,1.708 6.365,1.979 0.802,0.271 10 false H46 5.552,3.656 6.354,3.927 0.802,0.271 10 false H45

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Body Electrical > Power Source Control > Trouble Codes
50001 454

Result:
Result Proceed to
DTCs are not output A
DTC is output. B



A

2.READ VALUE USING GTS (SENSOR MALFUNCTION HISTORY)

B

GO TO ENTRY AND START SYSTEM (for Start Function) (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING GTS (SENSOR MALFUNCTION HISTORY)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sensor Malfunction History History of malfunction of position sensor in steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B278196 is stored) OK or NG OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) does not exist.
NG: History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator or upper bracket assembly) being on exists. (Under normal operation, neither sensor is on.)
When NG is displayed, either the position sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) or the assembly itself may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Sensor Malfunction History
50003 440 48
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

3.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Running Condition (Line) Vehicle being driven or stopped Stop or Driving Stop: Vehicle stopped
Driving: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Running Condition (Line)
50003 454 402
OK:

The GTS display changes correctly in response to the vehicle condition.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H71)Location & Routing

Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assembly

H71-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H71)Location & Routing

Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assembly

H71-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
B518305C11
1.49,0.99 1.896,1.25 0.406,0.26 2.354,2.885 1.885,2.885 1.885,2.885 1.885,1.979 true 2.719,2.677 2.25,2.677 2.25,2.677 2.25,1.99 true 0.188,0.281 0.5,0.438 0.313,0.156 10 false *a 1.573,1.031 2.073,1.302 0.5,0.271 10 false H71 2.448,2.802 2.948,3.073 0.5,0.271 10 false IGE 2.781,2.604 3.281,2.875 0.5,0.271 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H71)Location & Routing

Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assembly

H71-3 (IGE) - H71-1 (GND)

Steering lock motor operating when all conditions met, and then door opened:

-

The steering is unlocked.

-

The ignition switch is off.

-

The shift lever is in P.



11 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H71,H46)Location & Routing

Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assembly

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

H71-3 (IGE) - H46-24 (SLR+) Always Below 1 Ω
H71-3 (IGE) or H46-24 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C435466C01
1.49,0.938 1.906,1.198 0.417,0.26 2.344,2.948 1.896,2.948 1.896,2.948 1.896,1.969 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.385,2.844 2.792,3.01 0.406,0.167 10 false IGE 1.573,0.969 1.896,1.208 0.323,0.24 10 false H71
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H71)Location & Routing

Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assembly

H71-3 (IGE) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)