Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2020.08–2021.07
RM3700E _55 Steering _093030 STEERING COLUMN _0438540 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C441783N01
3.615,0.083 6.979,2.344 3.365,2.26 5.469,0.156 6.771,1.771 1.302,1.615 3.948,0.177 5.083,1.802 1.135,1.625 5.177,2.344 5.177,0.083 false 4.49,1.802 4.49,1.969 false 6.125,1.771 6.125,2.021 false 1.854,2.854 1.854,3.135 false 1.448,1.208 1.677,1.208 false 4.271,0.375 4.49,0.375 false 5.76,0.354 5.979,0.354 false 2.25,2.281 2.25,2.563 false 2.271,1.708 2.49,1.708 false 5.229,2.875 5.573,2.875 false 3.667,0.125 4.042,0.365 0.375,0.24 12 false *A 5.229,0.125 5.604,0.365 0.375,0.24 12 false *B 4.448,1.99 4.729,2.344 0.281,0.354 18 false 1 6.063,2.042 6.344,2.396 0.281,0.354 18 false 2 1.833,3.146 2.115,3.5 0.281,0.354 18 false 3 1.281,1.083 1.563,1.438 0.281,0.354 18 false 4 2.156,0.313 2.469,0.51 0.313,0.198 10 false x3 4.615,0.354 4.927,0.552 0.313,0.198 10 false x2 6.094,0.354 6.406,0.552 0.313,0.198 10 false x2 4.115,0.281 4.271,0.479 0.156,0.198 10 false ● 5.583,0.26 5.74,0.458 0.156,0.198 10 false ● 2.135,1.615 2.292,1.813 0.156,0.198 10 false ● 2.146,2.615 2.521,2.813 0.375,0.198 10 false ● *2 5.646,2.781 6.021,2.979 0.375,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING LOCK ACTUATOR ASSEMBLY 45020B (Click here) - -
2 UPPER STEERING COLUMN BRACKET WITH SWITCH ASSEMBLY 45020B - - -
3 BRACKET - (Click here) - -
4 POWER STEERING ECU ASSEMBLY 89650 (Click here) - -

*A w/ Entry and Start System *B w/o Entry and Start System
*1 ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY *2 CLIP BAND
● Non-reusable part - -

C441784N01
5.292,0.51 5.531,0.51 false 4.208,0.823 4.208,1.167 false 3.656,1.802 3.656,2.063 false 1.823,1.5 1.823,1.844 false 2.99,1.24 2.99,1.583 false 5.604,0.385 5.885,0.74 0.281,0.354 18 false 5 3.646,2.104 3.927,2.458 0.281,0.354 18 false 6 4.25,1.208 4.531,1.563 0.281,0.354 18 false 7 1.76,1.875 2.042,2.229 0.281,0.354 18 false 8 0.073,0.063 0.448,0.302 0.375,0.24 12 false *A 2.927,1.604 3.24,1.802 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

5 TRANSPONDER KEY COIL 89782 - - -
6 UN-LOCK WARNING SWITCH ASSEMBLY 84052 (Click here) - -
7 IGNITION SWITCH LOCK CYLINDER ASSEMBLY - (Click here) - -
8 IGNITION OR STARTER SWITCH ASSEMBLY 84450 - - -

*A w/o Entry and Start System - -
*1 UPPER STEERING COLUMN BRACKET ASSEMBLY - -

CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness.

·

Do not allow any moisture to come into contact with the power steering ECU with motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU with motor assembly.



PROCEDURE

Hide 45020B 1.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

a.
C431400N02
3.656,0.208 3.49,0.313 false 0.49,0.104 0.635,0.406 0.146,0.302 18 false i 2.854,0.104 3.083,0.417 0.229,0.313 18 false ii 5.219,0.104 5.833,0.427 0.615,0.323 18 false iii, iv 3.708,0.125 4.073,0.323 0.365,0.198 10 false SST

i.

Secure the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



ii.

Using SST, strike a punch mark for drilling in the center of the steering lock set bolt.

SST
09622-00010  

NOTICE:

When striking the punch mark, in order to prevent impact force from being applied to the steering lock actuator assembly, do not use a normal center punch.



iii.

Using a drill, drill a hole in the 2 steering lock set bolts and insert a screw extractor.


iv.

Using the screw extractor, remove the 2 steering lock set bolts, upper steering column clamp and steering lock actuator assembly.



Hide 45020B 2.REMOVE UPPER STEERING COLUMN BRACKET WITH SWITCH ASSEMBLY (w/o Entry and Start System)

a.

Use the same procedure for the steering lock actuator assembly.


Hide 89650 4.REMOVE POWER STEERING ECU ASSEMBLY

Hide 89782 5.REMOVE TRANSPONDER KEY COIL (w/o Entry and Start System)

a.
C441785


Hide 84052 6.REMOVE UN-LOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C441786C01
4.427,1.365 4.708,1.719 0.281,0.354 18 false i 2.5,1.375 2.781,1.729 0.281,0.354 18 false ii
V100135

Insert
V113147

Remove in this direction


i.

Insert the key.


ii.

Disengage the claws to remove the un-lock warning switch assembly as shown in the illustration.



Hide 7.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.
C441787C01
1.115,0.292 1.396,0.646 0.281,0.354 18 false i 3.885,0.75 4.167,1.104 0.281,0.354 18 false ii
V100135

Push
V113147

Remove in this direction


i.

Turn the ignition switch to ACC.


ii.

Insert the tip of a screwdriver into the hole in the upper steering column bracket assembly, as shown in the illustration, and remove the ignition switch lock cylinder assembly.



Hide 84450 8.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C441788