If the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM will store this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B279A12 | Engine Immobiliser System Circuit Short to Battery | The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high. (1 trip detection logic*) | ·
Certification ECU (smart key ECU assembly) ·
ECM ·
Wire harness or connector |
Engine | A | DTC output confirmation operation:
Turn the ignition switch to ON and wait 6 seconds. |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | Engine cannot be started |
| DTC No. | Data List and Active Test |
|---|---|
| B279A12 | - |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the ECM or certification ECU (smart key ECU assembly), refer to Service Bulletin.
After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When DTC B279A12 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
Pre-procedure1
Turn the ignition switch off.
Procedure1
Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
Certification ECU (Smart Key ECU Assembly) |
*b | Waveform |
| *c | Approximately 160 ms. | *d | Approximately 270 ms. |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
|
Click Location & Routing(H45)Location & Routingewd_type=routing;type=c;code=H45 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=5 |
|||
| H45-5 (EFIO) - Body ground | Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Result | Proceed to |
|---|---|
| 11 to 14 V | A |
| Below 1 V | B |
| Normal wavform | C |
A
B
C
Pre-procedure1
Disconnect the A54 ECM connector.
Disconnect the H45 certification ECU (smart key ECU assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54,H45)Location & Routingewd_type=routing;type=c,c;code=A54,H45 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=61 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=4 |
||
| A54-61 (IMO) - H45-4 (EFII) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG