Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › ECM › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442020 ECM A

M15A-FKS ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A494117N01
2.771,2 3.104,2 false 4.156,1.99 4.49,1.99 false 6.021,1.073 6.354,1.073 false 3.604,0.49 3.771,0.49 3.771,0.49 3.958,1.302 false 6.458,0.302 6.792,0.302 false 2.594,1.833 2.875,2.188 0.281,0.354 18 false 5 3.979,1.833 4.26,2.188 0.281,0.354 18 false 4 6.438,0.917 6.719,1.271 0.281,0.354 18 false 2 3.406,0.375 3.688,0.729 0.281,0.354 18 false 3 5.083,1.948 5.365,2.302 0.281,0.354 10 false x2 6.271,0.125 6.552,0.479 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 BATTERY 28800 - - -
3 ECM 89661 (Click here) - -
4 NO. 2 ECM BRACKET 89668 - - -
5 NO. 1 ECM BRACKET 89667E - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
If possible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
If impossible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


ECU security key
·

DTCs are stored

·

Vehicle control history (RoB) are stored


(Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART

·

Perform the Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



Hide 89661 3.REMOVE ECM

a.
A458041N01
0.531,0.094 1.906,0.448 1.375,0.354 18 false i, ii, iii

i.

Raise the 2 lock levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



ii.

Disengage the 2 clamps.


iii.

Remove the bolt, 2 nuts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.




Hide 89668 4.REMOVE NO. 2 ECM BRACKET

a.
A458597


Hide 89667E 5.REMOVE NO. 1 ECM BRACKET

a.
A458042