Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for Gasoline Model without Entry and Start System)
RM3700E _58 Vehicle Interior _093748 THEFT DETERRENT / KEYLESS ENTRY _0441969 IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B279A12 Engine Immobiliser System Circuit Short to Battery Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Wire harness or connector

·

ECM

·

Transponder key ECU assembly


Engine A
DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

E366880E23
5.052,0.833 5.365,1.031 0.313,0.198 10 false 11 1.813,0.833 2.219,1.031 0.406,0.198 10 false IMI 1.281,1.969 2.229,2.198 0.948,0.229 10 false A54 5.25,2.115 6.635,2.625 1.385,0.51 10 false Transponder Key ECU Assembly 2.104,0.833 2.917,1.063 0.813,0.229 10 false 61 5.302,0.844 5.708,1.042 0.406,0.198 10 false EFIO 1.323,0.385 1.74,0.594 0.417,0.208 10 false 12 V 5.24,1.948 5.646,2.146 0.406,0.198 10 false H74 1.271,2.146 3.417,2.698 2.146,0.552 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK ECM

NG

CONNECT CONNECTORS PROPERLY

2.CHECK ECM

Pre-procedure1

a.

Disconnect the H74 transponder key ECU assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H74)Location & Routing

Click Connector(H74)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transponder Key ECU Assembly

H74-11 (EFIO) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

Pre-procedure1

a.

Connect the transponder key ECU assembly connector.


Procedure1

b.

Using an oscilloscope, check the waveform.

B463095C21
3.396,0.385 3.781,0.656 0.385,0.271 2.99,2.198 3.229,1.552 true 3.24,4.563 3.292,4.083 true 3.521,4.563 3.479,4.083 true 0.375,0.125 0.688,0.323 0.313,0.198 10 false *a 3.458,0.427 3.771,0.625 0.313,0.198 10 false H74 2.646,2.219 3.104,2.448 0.458,0.229 10 false EFIO 3.333,3.021 3.792,3.25 0.458,0.229 10 false *b 0.958,4.042 1.417,4.271 0.458,0.229 10 false GND 3.052,4.531 3.313,4.719 0.26,0.188 10 false *c 3.552,4.552 3.813,4.74 0.26,0.188 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H74)Location & Routing

Click Connector(H74)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transponder Key ECU Assembly

H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the A54 ECM connector.


b.

Disconnect the H74 transponder key ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H74,A54)Location & Routing

Click Connector(H74)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transponder Key ECU Assembly

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

H74-11 (EFIO) - A54-61 (IMI) Always Below 1 Ω
H74-11 (EFIO) or A54-61 (IMI) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR