Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0442660 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering sensor power source
·

Harness or connector

·

Steering sensor


Rear Camera A

WIRING DIAGRAM

C402935E08
0.344,0.615 1.802,0.833 1.458,0.219 10 false from Auxiliary Battery 0.323,1 1.781,1.219 1.458,0.219 10 false from IGR-NO. 1 Relay 2.031,0.792 3.229,1 1.198,0.208 10 false ECU-DCC NO. 1 2.104,1.198 3.563,1.417 1.458,0.219 10 false ECU-IGR NO. 1 3.354,1.875 3.771,2.083 0.417,0.208 10 false H39 3.344,2.042 4.563,2.26 1.219,0.219 10 false Steering Sensor 5.313,2.073 6.781,2.448 1.469,0.375 10 false Rear Television Camera Assembly 3.156,0.552 3.365,0.802 0.208,0.25 10 false 4 3.156,0.958 3.365,1.208 0.208,0.25 10 false 9 3.135,1.333 3.344,1.583 0.208,0.25 10 false 6 3.385,0.656 3.854,0.875 0.469,0.219 10 false BAT 3.385,0.969 3.854,1.188 0.469,0.219 10 false IG*1 3.385,1.125 3.854,1.344 0.469,0.219 10 false IGR*2 3.375,1.448 3.844,1.667 0.469,0.219 10 false ESS 0.635,2.354 2.698,2.573 2.063,0.219 10 false : CAN Communication Line 0.323,1.531 2.385,1.75 2.063,0.219 10 false *1: for HV Model 0.313,1.875 1.938,2.104 1.625,0.229 10 false *2: for Gasoline Model

CAUTION / NOTICE / HINT

NOTICE:
·

When the "!" mark is displayed on the radio and display receiver assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for Gasoline Model A
for HV Model B



A

2.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE AND BODY GROUND)

Pre-procedure1

a.

Disconnect the H39 steering sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-6 (ESS) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-9 (IGR) - H39-6 (ESS) Ignition switch ON 11 to 14 V
H39-4 (BAT) - H39-6 (ESS) Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE AND BODY GROUND)

Pre-procedure1

a.

Disconnect the H39 steering sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-6 (ESS) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-9 (IG) - H39-6 (ESS) Ignition switch ON 11 to 14 V
H39-4 (BAT) - H39-6 (ESS) Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR