Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443936 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B638008N01
2.75,1.5 4.5,3.25 1.75,1.75 1.083,4.99 1.083,5.323 false 6.521,0.177 6.854,0.177 false 1.729,0.75 2.063,0.75 false 4.156,2.208 4.156,2.542 false 6.76,1.667 6.76,2 false 5.385,2.5 5.385,2.833 false 3.125,2.552 3.125,2.885 false 3.583,3.25 3.583,3.5 false 6.677,1.99 6.958,2.344 0.281,0.354 18 false 1 6.344,0.031 6.625,0.385 0.281,0.354 18 false 3 1.104,5.302 1.385,5.656 0.281,0.354 18 false 4 2.104,0.583 2.385,0.938 0.281,0.354 18 false 5 4.094,2.552 4.375,2.906 0.281,0.354 10 false *1 3.156,2.854 3.438,3.208 0.281,0.354 18 false 7 2.125,4.208 2.438,4.406 0.313,0.198 10 false x3 5.406,2.802 5.688,3.156 0.281,0.354 18 false 2 3.583,3.49 3.865,3.844 0.281,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HORN BUTTON ASSEMBLY 45130 - - -
2 STEERING WHEEL ASSEMBLY 45100 (Click here) - -
3 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
4 LOWER STEERING COLUMN COVER 45287 (Click here) - -
5 UPPER STEERING COLUMN COVER 45286B - - -
6 SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - (Click here) - -
7 STEERING SENSOR 89245B (Click here) - -

*1 SPIRAL CABLE SUB-ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the spiral cable with sensor sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (Click here)

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 45130 1.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 2.REMOVE STEERING WHEEL ASSEMBLY

Hide 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

a.
B597001C01
6.885,0.604 5.865,1.094 true 6.875,1.49 5.833,1.156 true 4.385,0.063 4.667,0.417 0.281,0.354 18 false ii 6.896,0.479 7.146,0.677 0.25,0.198 10 false *a 6.885,1.438 7.125,1.625 0.24,0.188 10 false *b 0.115,0.083 0.396,0.438 0.281,0.354 18 false i
*a Check Window *b Top of Flat Cable U-turn


i.

Check that the front wheels are facing straight ahead.


ii.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the result is not as specified, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 45287 4.REMOVE LOWER STEERING COLUMN COVER

Z101186

Click here(Click here)

Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

Hide 6.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch (for Gasoline Model) or power switch (for HV Model) on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch (for Gasoline Model) or power switch (for HV Model) on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.




a.
B596997C01
1.677,0.802 0.677,0.802 true 0.5,0.708 0.813,0.865 0.313,0.156 10 false *a 4.615,0.104 4.896,0.458 0.281,0.354 18 false ii 0.167,0.094 0.448,0.448 0.281,0.354 18 false i 0.354,1.771 0.729,2.01 0.375,0.24 12 false *A 2.729,1.813 3.104,2.052 0.375,0.24 12 false *B
*A w/ Smart Entry and Start System *B w/o Smart Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592966N01
1.229,1.24 1.51,1.594 0.281,0.354 18 false i 1.229,1.552 1.51,1.906 0.281,0.354 18 false ii 2.281,1.115 2.563,1.469 0.281,0.354 18 false ii 2.813,1.458 3.094,1.813 0.281,0.354 18 false ii 2.615,2.052 2.896,2.406 0.281,0.354 18 false iii 4.531,1.25 4.813,1.604 0.281,0.354 18 false iv 5.875,1.271 6.156,1.625 0.281,0.354 18 false iv 5.146,0.573 5.427,0.927 0.281,0.354 18 false iv

i.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



ii.

Disconnect each connector.


iii.

Separate the wire harness from the spiral cable with sensor sub-assembly.


iv.

Disengage the claw and clips to remove the spiral cable with sensor sub-assembly.



Hide 89245B 7.REMOVE STEERING SENSOR

Z101186

NOTICE:

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.
B585634N01
0.417,0.135 0.698,0.49 0.281,0.354 18 false i 3.188,0.125 3.469,0.479 0.281,0.354 18 false ii

i.

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable sub-assembly.

·

Do not remove the lock pin before installing the steering sensor to the spiral cable sub-assembly.




ii.

Disengage the claws and pins to remove the spiral cable sub-assembly from the steering sensor.

NOTICE:

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.