Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0442662 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1683  Side Camera Feedback Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1683 Side Camera Feedback Malfunction Side camera feedback malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH

·

Outer rear view mirror assembly LH


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E379403E26
5.708,2.823 6.167,3.021 0.458,0.198 10 false O25 5.708,3.01 7.031,3.417 1.323,0.406 10 false Parking Assist ECU 0.948,3.01 3.583,3.375 2.635,0.365 10 false Outer Rear View Mirror Assembly LH 0.74,2.365 3.156,2.615 2.417,0.25 10 false Side Television Camera Assembly LH 0.948,2.844 1.406,3.042 0.458,0.198 10 false L8 5.969,2.323 6.667,2.563 0.698,0.24 10 false SGND 5.979,1.896 6.677,2.135 0.698,0.24 10 false LGND 5.979,1.469 6.677,1.708 0.698,0.24 10 false LCV- 5.969,1.083 6.667,1.323 0.698,0.24 10 false LCV+ 5.969,0.656 6.667,0.896 0.698,0.24 10 false LCB+ 3.406,0.573 4.104,0.813 0.698,0.24 10 false LCB+ 3.406,0.958 4.104,1.198 0.698,0.24 10 false LCV+ 3.427,1.375 4.125,1.615 0.698,0.24 10 false LCV- 3.396,1.802 4.094,2.042 0.698,0.24 10 false LGND 5.74,0.594 6.052,0.792 0.313,0.198 10 false 9 5.688,0.99 6,1.188 0.313,0.198 10 false 36 5.688,1.396 6,1.594 0.313,0.198 10 false 13 5.688,1.833 6,2.031 0.313,0.198 10 false 26 5.698,2.24 6.01,2.438 0.313,0.198 10 false 14 3.906,1.802 4.219,2 0.313,0.198 10 false 13 3.885,1.375 4.198,1.573 0.313,0.198 10 false 14 3.906,0.979 4.219,1.177 0.313,0.198 10 false 6 3.906,0.573 4.219,0.771 0.313,0.198 10 false 5 4.781,2.302 4.938,2.5 0.156,0.198 10 false * 0.417,3.458 1.448,3.771 1.031,0.313 10 false *: Shielded 1.219,0.698 1.917,0.938 0.698,0.24 10 false SCB+ 1.208,1.125 1.906,1.365 0.698,0.24 10 false SCV+ 1.208,1.51 1.906,1.75 0.698,0.24 10 false SCV- 1.188,1.938 1.885,2.177 0.698,0.24 10 false SGND 0.76,2.208 1.031,2.438 0.271,0.229 10 false A 1.708,0.594 2.021,0.792 0.313,0.198 10 false 1 1.719,0.969 2.031,1.167 0.313,0.198 10 false 3 1.708,1.365 2.021,1.563 0.313,0.198 10 false 7 1.708,1.813 2.021,2.01 0.313,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353
Result:
Proceed to
NEXT




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
Result:
Result Proceed to
DTCs are not output A
C1683 is output B




A

B

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the O25 parking assist ECU connector.


b.

Disconnect the L8 outer rear view mirror assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25,L8)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

O25-9 (LCB+) - L8-5 (LCB+) Always Below 1 Ω
O25-36 (LCV+) - L8-6 (LCV+) Always Below 1 Ω
O25-13 (LCV-) - L8-14 (LCV-) Always Below 1 Ω
O25-26 (LGND) - L8-13 (LGND) Always Below 1 Ω
O25-9 (LCB+) or L8-5 (LCB+) - Body ground Always 10 kΩ or higher
O25-36 (LCV+) or L8-6 (LCV+) - Body ground Always 10 kΩ or higher
O25-13 (LCV-) or L8-14 (LCV-) - Body ground Always 10 kΩ or higher
O25-26 (LGND) or L8-13 (LGND) - Body ground Always 10 kΩ or higher
O25-14 (SGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK PARKING ASSIST ECU (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK PARKING ASSIST ECU (LCV-, LGND)

Pre-procedure1

a.

Disconnect the O25 parking assist ECU connector.


Procedure1

a.
E432582C20
1.365,0.177 1.76,0.448 0.396,0.271 2.302,1.719 1.917,1.146 true 0.99,1.708 1.198,1.021 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 2.219,1.75 2.719,1.906 0.5,0.156 10 false LGND 0.854,1.75 1.354,1.906 0.5,0.156 10 false LCV- 1.427,0.208 1.927,0.365 0.5,0.156 10 false O25
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-26 (LGND) - Body ground Always Below 1 Ω
O25-13 (LCV-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

5.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.
E432581C27
1.396,0.25 1.896,0.5 0.5,0.25 2.667,1.844 1.917,1.146 true 1.948,1 2.531,0.344 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 2.594,0.271 2.99,0.427 0.396,0.156 10 false LCB+ 2.573,1.875 3.135,2.031 0.563,0.156 10 false LGND 1.521,0.271 2.115,0.49 0.594,0.219 10 false O25
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-26 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-9 (LCB+) - O25-26 (LGND) Ignition switch ON 5.5 to 7.05 V
O25-9 (LCB+) - O25-26 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

NG

6.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)
a.

Using an oscilloscope, check the waveform of the side television camera assembly LH.

HINT:

A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E444517C11
0.771,0.271 1.208,0.531 0.438,0.26 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.313,1.781 0.656,1.104 true 1.719,1.792 1.208,1.115 true 0.167,1.823 0.521,2.021 0.354,0.198 10 false LCV+ 1.594,1.813 2.073,1.99 0.479,0.177 10 false LGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.854,0.302 1.448,0.552 0.594,0.25 10 false O25
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly LH.

·

The video waveform is constantly output when the ignition switch is ACC.



Measurement Condition
Item Content
Tester Connection O25-36 (LCV+) - O25-26 (LGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


Procedure1

a.
E407112C43
1.552,0.094 1.885,0.302 0.333,0.208 0.344,2.354 0.708,2.583 0.365,0.229 2,0.75 2.406,0.333 2.406,0.333 2.531,0.333 true 1.979,1.083 2.281,1.417 2.281,1.417 2.406,1.417 true 1.75,2.688 1.542,3.177 1.542,3.177 1.406,3.177 true 1.927,2.688 2.167,3.167 2.167,3.167 2.292,3.167 true 1.781,2.458 1.521,1.781 1.521,1.781 1.385,1.781 true 1.938,2.427 2.208,1.771 2.208,1.771 2.333,1.771 true 1.396,0.75 1.104,0.365 1.104,0.365 0.969,0.365 true 1.427,1.031 1.042,1.396 1.042,1.396 0.906,1.396 true 0.25,0.156 0.448,0.313 0.198,0.156 10 false *a 0.25,1.802 0.448,1.958 0.198,0.156 10 false *b 1.667,0.115 1.823,0.281 0.156,0.167 10 false A 2.615,0.281 3.094,0.438 0.479,0.156 10 false SCB+ 2.5,1.354 2.927,1.51 0.427,0.156 10 false SGND 0.99,1.698 1.469,1.854 0.479,0.156 10 false LCB+ 1.021,3.104 1.5,3.26 0.479,0.156 10 false LGND 2.417,1.708 2.896,1.865 0.479,0.156 10 false LCV+ 2.385,3.094 2.865,3.25 0.479,0.156 10 false LCV- 0.563,0.313 1.042,0.469 0.479,0.156 10 false SCV+ 0.5,1.313 0.979,1.469 0.479,0.156 10 false SCV- 0.448,2.375 0.792,2.604 0.344,0.229 10 false L8
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L8)Location & Routing

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

A-1 (SCB+) - L8-5 (LCB+) Always Below 1 Ω
A-3 (SCV+) - L8-6 (LCV+) Always Below 1 Ω
A-7 (SCV-) - L8-14 (LCV-) Always Below 1 Ω
A-5 (SGND) - L8-13 (LGND) Always Below 1 Ω
A-1 (SCB+) or L8-5 (LCB+) - Body ground Always 10 kΩ or higher
A-3 (SCV+) or L8-6 (LCV+) - Body ground Always 10 kΩ or higher
A-7 (SCV-) or L8-14 (LCV-) - Body ground Always 10 kΩ or higher
A-5 (SGND) or L8-13 (LGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

8.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL



Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353
Result:
Proceed to
NEXT




NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
Result:
Result Proceed to
DTCs are not output A
C1683 is output B




A

END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE)

B