Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM L

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  PRECAUTION  


PRECAUTIONS FOR INSPECTING HYBRID CONTROL SYSTEM


a.
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

·

Inspecting the high-voltage system

·

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

·

Disconnecting the low voltage connector of the HV battery


A475619N01
2.146,1.792 2.271,1.948 0.125,0.156 10 true 1 1.24,1.25 1.365,1.406 0.125,0.156 10 true 2 5.135,1.635 5.25,1.792 0.115,0.156 10 true 3

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After removing the service plug grip, turning the ignition switch to ON (READY) may cause a malfunction. Do not turn the ignition switch to ON (READY) unless instructed by the repair manual.




b.
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


c.
A358042

After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


d.
A357589C04
1.563,0.708 1.813,0.417 true 1.844,0.302 2.156,0.5 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.



e.

Check the voltage at the terminals in the inspection point of the hybrid motor control inverter assembly.

CAUTION:

Be sure to wear insulated gloves.


i.
A475620

Remove the connector cover assembly from the hybrid motor control inverter assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL

NOTICE:
·

Do not touch the connector cover assembly waterproof seal.

·

Do not allow any foreign matter or water to enter the hybrid motor control inverter assembly.




ii.
A458475

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Inspection point At least 10 minutes after removing the service plug grip 0 V


HINT:

Make sure to set the tester to DC750 V or more when measuring the voltage.



iii.

Reinstall the connector cover assembly.



f.

Check the voltage at the terminals in the inspection point of the rear hybrid motor control inverter assembly.

CAUTION:

Wear insulated gloves.


i.
A475621C01
0.938,2.281 1.125,2.042 1.125,2.042 1.313,2.042 true 0.958,2.792 1.635,3.031 1.635,3.031 1.354,2.625 true 1.635,3.031 2.188,2.594 true 1.375,1.969 1.688,2.167 0.313,0.198 10 false *a 1.594,3.052 1.917,3.25 0.323,0.198 10 false *b
*a Interlock Connector
*b Waterproof Seal


Remove the 5 bolts and inverter terminal cover from the rear hybrid motor control inverter assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR INVERTER>REMOVAL

NOTICE:
·

Make sure to pull the connector cover assembly straight up, as a connector is connected to the bottom of the connector cover assembly.

·

Do not touch the connector cover assembly waterproof seal.

·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.




ii.
A475622N01
1.417,2.26 1.604,2.26 1.604,2.26 1.854,2.406 true 1.281,2.188 1.438,2.385 0.156,0.198 10 false A

Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.

Standard Voltage:
Tester Connection Condition Specified Condition
Inspection point At least 10 minutes after removing the service plug grip 0 V


NOTICE:
·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

As it may result in an incorrect measurement, do not use terminal (A) when measuring.



HINT:

Make sure to set the tester to DC750 V or more when measuring the voltage.




g.
A358019

w/ Entry and Start System:

When turning the power switch on (IG) during an inspection, do not press the power switch while depressing the brake pedal.

CAUTION:

Pressing the power switch with the brake pedal depressed causes the system to enter the READY-on state. This is very dangerous because high voltage may be applied to the inspection area.



h.
C414532

w/o Entry and Start System:

When turning the ignition switch to ON during inspections, do not turn the ignition switch to START.

CAUTION:

Turning the ignition switch to START causes the system to enter the READY-on state. This is very dangerous because high voltage may be applied to the inspection area.



i.

Turn the ignition switch off, disconnect the cable from the negative (-) terminal of the auxiliary battery and put on insulated gloves before touching any of the orange-colored wire harnesses and connectors of the high-voltage system.

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART





j.

Turn the ignition switch off before performing any resistance checks.


k.

Turn the ignition switch off before disconnecting or reconnecting any connectors.


l.

When performing work involving high-voltage wires, use either a tool wrapped with vinyl insulating tape or an insulated tool.


m.

When high-voltage connectors are removed, wrap the connectors with insulation tape to prevent them from contacting foreign matter.



NOTICE FOR HYBRID CONTROL SYSTEM ACTIVATION


a.

When the warning is illuminated, or the auxiliary battery has been disconnected and reconnected, attempting to turn the ignition switch to ON (READY) may not start the system (the system may not enter the READY-on state) on the first attempt. If so, turn the ignition switch off and reattempt to start the hybrid system.

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART