| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | ( )
|
- | - |
| 2 | SERVICE PLUG GRIP | G3834 | - | - | - |
| 3 | DECK BOARD ASSEMBLY | 58410B | - | - | - |
| 4 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 5 | HYBRID INVERTER PROTECTOR ASSEMBLY | G92D0 | ( )
|
- | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear hybrid motor control inverter assembly removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
G3834
2.REMOVE SERVICE PLUG GRIP
58410B
3.REMOVE DECK BOARD ASSEMBLY
64993
4.REMOVE REAR DECK FLOOR BOX
G92D0
5.REMOVE HYBRID INVERTER PROTECTOR ASSEMBLY
|
|
G9223
6.REMOVE INVERTER TERMINAL COVER
|
|
| *a | Interlock | *b | Waterproof Seal |
7.CHECK TERMINAL VOLTAGE
|
|
Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.
0 V
Use a measuring range of DC 750 V or more on the voltmeter.
821H1
8.DISCONNECT FLOOR UNDER WIRE
|
|
| *a | Waterproof Seal | - | - |
Using an insulated tool, remove the 4 bolts and disconnect the HV floor under wire from the rear hybrid motor control inverter assembly.
821H3
9.DISCONNECT HV BATTERY PACK WIRE
|
|
| *a | Interlock | *b | Waterproof Seal |
Using an insulated tool, remove the 4 bolts and disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.
10.DISCONNECT REAR TRACTION MOTOR CABLE
|
|
| *a | Waterproof Seal | - | - |
Using an insulated tool, remove the 5 bolts and disconnect the rear traction motor cable from the rear hybrid motor control inverter assembly.
G9223
11.TEMPORARILY INSTALL INVERTER TERMINAL COVER
|
|
Temporarily install the inverter terminal cover with the 5 bolts.
Temporarily install the inverter terminal cover with the 5 bolts.
G92B0
12.REMOVE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY
|
|
Disconnect the 2 rear hybrid motor control inverter assembly connectors.
Do not touch the waterproof seal or terminals of the connector.
Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.
Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.
Insulate the disconnected terminals with insulating tape.
To prevent damage due to staticelectricity, do not touch the terminals of the disconnected connectors.
Remove the 3 bolts and rear hybrid motor control inverter assembly.
Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.
Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.
Insulate the disconnected terminals with insulating tape.
To prevent damage due to staticelectricity, do not touch the terminals of the disconnected connectors.
G92B2
13.REMOVE HV INVERTER COOLING COVER
|
|
Using a T25 "TORX" socket wrench, remove the 4 bolts and HV inverter cooling cover from the rear hybrid motor control inverter assembly.
G92B1
14.REMOVE HV INVERTER COOLING FAN
|
|
Disconnect the rear hybrid motor control inverter assembly.
Disengage the clamp.
Disengage the 2 guides.
Using a T20 "TORX" socket wrench, remove the 3 bolts and HV inverter cooling fan from the rear hybrid motor control inverter assembly.