Refer to DTC P019011.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P019011
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P019015 | Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open | The fuel pressure sensor (for high pressure side) output voltage is higher than 4.9 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in fuel pressure sensor (for high pressure side) circuit ·
Fuel pressure sensor (for high pressure side) ·
ECM |
Comes on | Engine | A | SAE: P0193 |
When a DTC is output, check the Data List item "Fuel Pressure (High)" using the GTS.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| DTC No. | Fuel Pressure (High) | Malfunction |
|---|---|---|
| P019015 | Approximately 33000 kPag or higher | ·
Short in VCPR to PR circuit ·
Open in PR circuit ·
Open in EPR circuit |
If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
This DTC is stored if the fuel pressure sensor (for high pressure side) output voltage is out of the standard range due to an open or short in the sensor circuit.
Example:
If the fuel pressure sensor (for high pressure side) output voltage is higher than 4.9 V for 3 seconds or more, the ECM will illuminate the MIL and store this DTC.
| Required Sensors/Components | Fuel pressure sensor (for high pressure side) |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Idle the engine for 10 seconds.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P019015.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
Refer to DTC P019011.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P019011
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Pre-procedure1
Disconnect the fuel pressure sensor (for high pressure side) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(e2)Location & Routingewd_type=routing;type=c;code=e2 Click Connector(e2)Engine Compartment>Sensor Wire>No. 2 Fuel Pressure Sensorewd_type=component;type=c;code=e2;pinno=1,2,3 |
||
| e2-1 (VC) - e2-2 (E2) | Ignition switch ON | 4.75 to 5.25 V |
| e2-3 (PR) - e2-2 (E2) | Ignition switch ON | 3.0 to 5.25 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(e2)Location & Routingewd_type=routing;type=c;code=e2 Click Connector(e2)Engine Compartment>Sensor Wire>No. 2 Fuel Pressure Sensorewd_type=component;type=c;code=e2;pinno=2,1,3 |
||
| e2-2 (E2) - Body ground | Ignition switch off | Below 1 Ω |
| e2-1 (VC) - e2-3 (PR) | Ignition switch off | 171 to 189 kΩ |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL PRESSURE SENSOR (for High Pressure)>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
NG
Pre-procedure1
Disconnect the fuel pressure sensor (for high pressure side) connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(e2,D51)Location & Routingewd_type=routing;type=c,c;code=e2,D51 Click Connector(e2)Engine Compartment>Sensor Wire>No. 2 Fuel Pressure Sensorewd_type=component;type=c;code=e2;pinno=3,2 Click Connector(D51)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D51;pinno=97,96 |
||
| e2-3 (PR) - D51-97 (PR) | Always | Below 1 Ω |
| e2-2 (E2) - D51-96 (EPR) | Always | Below 1 Ω |
| e2-3 (PR) or D51-97 (PR) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG