Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P05042B  Brake Switch "A"/"B" Signal Cross Coupled  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores this DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).


On the GTS, Data List item Stop Light SW is ON when the brake pedal is depressed.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P05042B Brake Switch "A"/"B" Signal Cross Coupled Conditions (a) and (b) are met for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON
(b) STP signal OFF when ST1- signal OFF
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- Engine A SAE: P0504

WIRING DIAGRAM

A459177E01
0.792,0.573 1.198,0.75 0.406,0.177 10 false STOP 0.635,3.333 1.833,3.552 1.198,0.219 10 false BATT-MAIN NO.1 3.146,3.323 3.781,3.521 0.635,0.198 10 false IGP-MAIN 0.781,3.615 2.646,3.958 1.865,0.344 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.781,4.219 3.521,4.521 2.74,0.302 10 false from Ignition Switch Assembly*2 0.563,4.5 1.083,4.677 0.521,0.177 10 false Battery 3.573,0.302 3.854,0.469 0.281,0.167 10 false 7 3.573,0.792 3.854,0.958 0.281,0.167 10 false 6 3.563,1.26 3.844,1.427 0.281,0.167 10 false 2 3.76,0.438 3.938,0.615 0.177,0.177 10 false B 3.76,0.938 3.938,1.115 0.177,0.177 10 false B 3.75,1.375 4.104,1.552 0.354,0.177 10 false GND 4.635,0.417 4.813,0.594 0.177,0.177 10 false L 4.646,1.365 4.823,1.542 0.177,0.177 10 false L 5.698,0.323 5.885,0.469 0.188,0.146 10 false 21 5.688,1.271 5.875,1.417 0.188,0.146 10 false 22 4.854,0.313 5.135,0.479 0.281,0.167 10 false 3 4.833,1.25 5.115,1.417 0.281,0.167 10 false 5 3.417,1.698 3.875,1.875 0.458,0.177 10 false A63 3.406,1.865 5.656,2.073 2.25,0.208 10 false Stop Light Switch Assembly 5.948,0.323 6.271,0.479 0.323,0.156 10 false STP 5.938,1.281 6.302,1.438 0.365,0.156 10 false ST1- 3.427,2.771 4.365,2.938 0.938,0.167 10 false ECU-IGP NO.3 4.417,3.906 4.719,4.063 0.302,0.156 10 false IGP 6.25,4.396 6.563,4.573 0.313,0.177 10 false A54 6.25,4.583 6.76,4.927 0.51,0.344 10 false ECM 0.406,1.719 1.448,1.917 1.042,0.198 10 false INP STD NO.1-3 1.208,5.021 5.031,5.219 3.823,0.198 10 false *1: w/ Entry and Start System 1.219,5.375 5.198,5.573 3.979,0.198 10 false *2: w/o Entry and Start System 4.115,3.5 4.271,3.698 0.156,0.198 10 false 1 4.875,3.51 5.031,3.708 0.156,0.198 10 false 2 4.104,3.094 4.26,3.292 0.156,0.198 10 false 3 4.885,3.104 5.042,3.302 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Stop light switch assembly conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light SW
Depressed ON
Released OFF


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-7 (B) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-6 (B) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-2 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

Pre-procedure1

a.
F102339C06
0.729,0.229 1.042,0.427 0.313,0.198 10 *a 2.583,0.219 2.896,0.417 0.313,0.198 10 *b
*a Brake Pedal Depressed
*b Brake Pedal Released


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition

Click Location & Routing(A54)Location & Routing

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

A54-22 (ST1-) - Body ground Depressed Below 1.5 V
A54-21 (STP) - Body ground Depressed 7.5 to 14 V
A54-22 (ST1-) - Body ground Released 7.5 to 14 V
A54-21 (STP) - Body ground Released Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63,A54)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

A63-5 (L) - A54-22 (ST1-) Always Below 1 Ω
A63-3 (L) - A54-21 (STP) Always Below 1 Ω
A63-5 (L) or A54-22 (ST1-) - Body ground and other terminals Always 10 kΩ or higher
A63-3 (L) or A54-21 (STP) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the stop light switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

5 (IGP relay) - A63-6 (B) Always Below 1 Ω
5 (IGP relay) or A63-6 (B) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

Pre-procedure1

a.

Disconnect the IGP relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGP relay) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR