The fuel pressure sensor (for low pressure side) replaces the fuel pressure with electrical signals and outputs them to the ECM. The ECM controls the optimal fuel pressure for the operation conditions to reduce the fuel pump power consumption and improve fuel economy.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P107A11 | Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Ground | The fuel pressure sensor (for low pressure side) output voltage is below 0.43 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in fuel pressure sensor (for low pressure side) circuit ·
Fuel pressure sensor (for low pressure side) ·
ECM |
Comes on | Engine | A | SAE: P107C |
When a DTC is output, check the Data List item "Fuel Pressure (Low) / Fuel Pressure 2" using the GTS.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| DTC No. | Fuel Pressure (Low) / Fuel Pressure 2 | Malfunction |
|---|---|---|
| P107A11 | Approximately 0 kPag | ·
Short to ground in PFL circuit ·
Short in PFL to EPFL circuit ·
Open in VCPF circuit |
If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
This DTC is stored if the fuel pressure sensor (for low pressure side) output voltage is out of the standard range due to an open or short in the sensor circuit.
| Required Sensors/Components | Fuel pressure sensor (for low pressure side) |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Idle the engine for 10 seconds or more [A].
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P107A11.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [A] through [B] again.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Pre-procedure1
Disconnect the fuel pressure sensor (for low pressure side) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D27)Location & Routingewd_type=routing;type=c;code=D27 Click Connector(D27)Engine Compartment>Engine Wire>Fuel Pressure Sensorewd_type=component;type=c;code=D27;pinno=1,3,2 |
||
| D27-1 (VC) - D27-3 (E2) | Ignition switch ON | 4.75 to 5.25 V |
| D27-2 (PFL) - D27-3 (E2) | Ignition switch ON | 4.4 to 5.6 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D27)Location & Routingewd_type=routing;type=c;code=D27 Click Connector(D27)Engine Compartment>Engine Wire>Fuel Pressure Sensorewd_type=component;type=c;code=D27;pinno=1,2 |
||
| D27-1 (VC) - D27-2 (PFL) | Ignition switch off | 171 to 189 kΩ |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL PRESSURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
NG
Pre-procedure1
Disconnect the fuel pressure sensor (for low pressure side) connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D27,D51)Location & Routingewd_type=routing;type=c,c;code=D27,D51 Click Connector(D27)Engine Compartment>Engine Wire>Fuel Pressure Sensorewd_type=component;type=c;code=D27;pinno=1,2 Click Connector(D51)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D51;pinno=84,107 |
||
| D27-1 (VC) - D51-84 (VCPF) | Always | Below 1 Ω |
| D27-2 (PFL) or D51-107 (PFL) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG