Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P212012  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery  P212014  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open  P21201C  Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range  P21201F  Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent  P212099  Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit  P212512  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery  P212514  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open  P21251F  Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent  P21382B  Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation Signal Cross Coupled  


DESCRIPTION

HINT:

These DTCs relate to the accelerator pedal position sensor.


The accelerator pedal position sensor is built into the accelerator pedal (with sensor) rod assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A255815E70
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.844,2.875 0.552,3.281 false 1.063,2.198 1.26,1.365 1.26,1.365 1.396,1.365 false 4.333,1.833 3.844,0.938 false 1.063,2.563 0.927,1.823 false 0.927,1.823 0.854,1.823 false 1.302,3.615 1.146,3.615 1.146,3.615 1,3.26 false 0.292,3.802 1.969,4.177 1.677,0.375 10 false Accelerator Pedal Position Sensor 1.448,1.302 1.927,1.479 0.479,0.177 10 false Magnet 0.313,1.74 0.844,1.917 0.531,0.177 10 false IC No. 1 0.313,3.313 0.844,3.49 0.531,0.177 10 false IC No. 2 2.063,1.74 2.531,1.917 0.469,0.177 10 false VPA 2.063,2.073 2.552,2.271 0.49,0.198 10 false EPA 2.063,2.385 2.583,2.563 0.521,0.177 10 false VCPA 2.063,2.688 2.573,2.865 0.51,0.177 10 false VPA2 2.063,3 2.563,3.198 0.5,0.198 10 false EPA2 2.063,3.323 2.583,3.5 0.521,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.854 4.208,2.031 0.292,0.177 10 false 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 false 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 false 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 false 3.188 3.969,2.823 4.271,3 0.302,0.177 10 false 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 false 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.073,3.771 0.292,0.177 10 false 12.4 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.667,3.896 7.167,4.094 2.5,0.198 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 false VPA 6.438,1.823 6.865,2 0.427,0.177 10 false VPA2 1.375,3.531 1.854,3.708 0.479,0.177 10 false Magnet

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P212012 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery VPA is 4.8 V or higher for 2 seconds or more (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open in EPA circuit

·

Short in VPA circuit

·

ECM


Comes on Engine A SAE: P2123
P212014 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


Comes on Engine A SAE: P2122
P21201C Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range Difference between VPA and VPA2 is greater than or equal to the specified value for 0.5 seconds (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

ECM


Comes on Engine A SAE: P2121
P21201F Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Accelerator pedal (with sensor) rod assembly circuit

·

ECM


Comes on Engine A SAE: P2120
P212099 Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit Difference between VPA and VPA2 is below 0.4 V, or higher than 1.2 V (learned value of accelerator off position) (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

ECM


Comes on Engine A SAE: P2121
P212512 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator pedal (with sensor) rod assembly

·

Open in EPA2 circuit

·

Short in VPA2 circuit

·

ECM


Comes on Engine A SAE: P2128
P212514 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


Comes on Engine A SAE: P2127
P21251F Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Accelerator pedal (with sensor) rod assembly circuit

·

ECM


Comes on Engine A SAE: P2125
P21382B Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation Signal Cross Coupled Difference between VPA and VPA2 is 0.02 V or less for 2.0 seconds or more (1 trip detection logic):
·

Accelerator pedal (with sensor) rod assembly

·

Short between VPA and VPA2 circuits

·

ECM


Comes on Engine A SAE: P2138

HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage using the GTS. Enter the following menus: Powertrain / Engine / Data List / Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage.

Trouble Area Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage
Open in VCP circuit 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
Open in EPA circuit 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits exceeds the upper or lower threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully depressed, DTC P212014 is stored.

MONITOR STRATEGY

Required Sensors/Components Accelerator pedal (with sensor) rod assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

P212012, P212014, P21201F, P212512, P212514, P21251F and P21382B
A403176E10
2.177,2.438 2.469,1.958 2.469,1.958 2.625,1.958 false 4.677,2.448 4.969,1.969 4.969,1.969 5.125,1.969 false 3.677,1.906 2.844,1.26 2.844,1.26 3,1.26 false 0.198,0.125 3.719,0.323 3.521,0.198 10 false Accelerator Pedal State 0.865,0.469 1.708,0.76 0.844,0.292 10 false Depressed 0.938,0.896 1.781,1.188 0.844,0.292 10 false Released 0.448,2.354 2.208,2.927 1.76,0.573 10 false Ignition Switch ON 2.177,2.5 2.5,2.75 0.323,0.25 10 false [A] 3.875,1.906 4.198,2.156 0.323,0.25 10 false [B] 4.385,3.427 4.708,3.677 0.323,0.25 10 false [C] 2.635,3.083 3.948,3.344 1.313,0.26 10 false 5 seconds or more 2.719,1.875 3.469,2.104 0.75,0.229 10 false Released 5.208,1.896 5.958,2.125 0.75,0.229 10 false Released 3.083,1.188 3.833,1.417 0.75,0.229 10 false Depressed

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Fully depress and release the accelerator pedal [B].

9.

Check that 5 seconds or more have elapsed since the ignition switch to ON.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P212012, P212014, P21201F, P212512, P212514, P21251F or P21382B.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.





P21201C and P212099
A256657E86
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.438 2.438,2.094 2.438,2.094 2.542,2.094 false 0.125,0.094 1.74,0.271 1.615,0.177 10 false Accelerator Pedal State 0.865,0.417 1.583,0.563 0.719,0.146 10 false Depressed 0.948,0.875 1.594,1.031 0.646,0.156 10 false Released 0.458,2.406 1.906,2.792 1.448,0.385 10 false Ignition Switch ON 2.094,2.49 2.469,2.688 0.375,0.198 10 false [A] 4.417,3.438 4.844,3.615 0.427,0.177 10 false [C] 5.365,1.719 6.01,1.875 0.646,0.156 10 false Released 2.375,3.052 3.188,3.229 0.813,0.177 10 false 5 seconds 3.01,1.229 3.729,1.375 0.719,0.146 10 false Depressed 3.865,3.042 4.208,3.24 0.344,0.198 10 false [B] 2.594,2.01 3.24,2.167 0.646,0.156 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Wait for 5 seconds after turning the ignition switch to ON.

9.

Operate the accelerator pedal in accordance with the following procedure [B].

(a)

Enter the following menus: Powertrain / Engine / Data List / Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %.

(b)

Slowly depress the accelerator pedal until Accelerator Position Sensor No.1 Voltage % is approximately 30% and Accelerator Position Sensor No.2 Voltage % is approximately 46%, then slowly release the accelerator pedal.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P21201C or P212099.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.





FAIL-SAFE

When these DTCs are stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A403187E22
0.438,3.167 3.427,3.5 2.99,0.333 10 false Accelerator Pedal Position Sensor (Accelerator Pedal (with Sensor) Rod Assembly) 0.115,3.167 0.469,3.375 0.354,0.208 10 false A62 2.042,0.5 2.583,0.708 0.542,0.208 10 false 6 1.573,1.063 2.115,1.271 0.542,0.208 10 false EPA 1.479,1.469 2.021,1.677 0.542,0.208 10 false VCPA 1.5,1.875 2.042,2.083 0.542,0.208 10 false VPA2 1.5,2.292 2.042,2.5 0.542,0.208 10 false EPA2 1.5,2.708 2.042,2.917 0.542,0.208 10 false VCP2 1.573,0.615 2.115,0.823 0.542,0.208 10 false VPA 2.042,0.917 2.583,1.125 0.542,0.208 10 false 5 2.042,1.333 2.583,1.542 0.542,0.208 10 false 4 2.031,1.75 2.573,1.958 0.542,0.208 10 false 3 2.031,2.167 2.573,2.375 0.542,0.208 10 false 2 2.031,2.594 2.573,2.802 0.542,0.208 10 false 1 5.656,3.167 6.198,3.375 0.542,0.208 10 false A54 5.99,3.167 6.531,3.375 0.542,0.208 10 false ECM 5.635,0.5 6.177,0.708 0.542,0.208 10 false VPA 5.604,1.177 6.146,1.385 0.542,0.208 10 false EPA 5.615,1.365 6.156,1.573 0.542,0.208 10 false VCPA 5.615,1.76 6.156,1.969 0.542,0.208 10 false VPA2 5.625,2.417 6.167,2.625 0.542,0.208 10 false EPA2 5.625,2.604 6.167,2.813 0.542,0.208 10 false VCP2 5.281,0.49 5.521,0.708 0.24,0.219 10 false 55 5.281,0.906 5.521,1.125 0.24,0.219 10 false 56 5.281,1.323 5.521,1.542 0.24,0.219 10 false 57 5.281,1.74 5.521,1.958 0.24,0.219 10 false 58 5.281,2.156 5.521,2.375 0.24,0.219 10 false 59 5.281,2.583 5.521,2.802 0.24,0.219 10 false 60 6.344,1.24 6.677,1.469 0.333,0.229 10 false 5 V 6.344,2.5 6.677,2.729 0.333,0.229 10 false 5 V 5.833,0.865 6.365,1.052 0.531,0.188 10 false 39 kΩ 5.823,2.104 6.354,2.292 0.531,0.188 10 false 39 kΩ

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
a.

Read the value displayed on the GTS when the accelerator pedal is released.

Powertrain > Engine > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage
Accelerator Position Sensor No.2 Voltage
50003 372 87,88
Standard Voltage:
Accelerator Pedal Operation Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V


Result:
Result Proceed to
The difference between the value of Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage is higher than 0.02 V A
None of the above conditions are met B




A

2.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

B

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY)
2.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
a.

Read the value displayed on the GTS when the accelerator pedal is depressed.

Powertrain > Engine > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage
Accelerator Position Sensor No.2 Voltage
50003 372 87,88
Standard Voltage:
Accelerator Pedal Operation Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V


Result:
Result Proceed to
The difference between the value of Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage is higher than 0.02 V A
None of the above conditions are met B




A

B

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY)
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY)
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A62)Location & Routing

Click Connector(A62)Instrument Panel>Engine Room Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

A62-4 (VCPA) - A62-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A62-1 (VCP2) - A62-2 (EPA2) Ignition switch ON 4.5 to 5.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

4.CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)

NG

6.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)

Pre-procedure1

a.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A62)Location & Routing

Click Connector(A62)Instrument Panel>Engine Room Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

A62-6 (VPA) - A62-5 (EPA) Ignition switch off 28.00 to 40.95 kΩ
A62-3 (VPA2) - A62-2 (EPA2) Ignition switch off 28.00 to 40.95 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A62,A54)Location & Routing

Click Connector(A62)Instrument Panel>Engine Room Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

A62-6 (VPA) - A54-55 (VPA) Always Below 1 Ω
A62-5 (EPA) - A54-56 (EPA) Always Below 1 Ω
A62-3 (VPA2) - A54-58 (VPA2) Always Below 1 Ω
A62-2 (EPA2) - A54-59 (EPA2) Always Below 1 Ω
A62-6 (VPA) or A54-55 (VPA) - Body ground and other terminals Always 10 kΩ or higher
A62-5 (EPA) or A54-56 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A62-3 (VPA2) or A54-58 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A62-2 (EPA2) or A54-59 (EPA2) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A62,A54)Location & Routing

Click Connector(A62)Instrument Panel>Engine Room Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

A62-4 (VCPA) - A54-57 (VCPA) Always Below 1 Ω
A62-5 (EPA) - A54-56 (EPA) Always Below 1 Ω
A62-1 (VCP2) - A54-60 (VCP2) Always Below 1 Ω
A62-2 (EPA2) - A54-59 (EPA2) Always Below 1 Ω
A62-4 (VCPA) or A54-57 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
A62-5 (EPA) or A54-56 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A62-1 (VCP2) or A54-60 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
A62-2 (EPA2) or A54-59 (EPA2) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR