To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P044313 | Evaporative Emission System Purge Control Valve "A" Circuit Open | Both of the following conditions (a) and (b) are met (1 trip detection logic):
(a) The purge VSV operation duty signal is 5 to 95%. (b) The target control value and actual control value do not match for 10 seconds or more. |
·
Open or short in purge VSV circuit ·
Purge VSV ·
ECM |
Comes on | Engine | A | SAE: P0443 |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
The A/C switch and all accessory switches should be off.
Idle the engine for 15 minutes or more [B].
Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P044313.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform steps [D] through [E].
Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P044313.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Inspect the fuses of circuits related to this system before performing the following procedure.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | VSV is on |
| *b | VSV is off |
Pre-procedure1
Disconnect the fuel vapor feed hose (on the canister side) from the purge VSV.
Start the engine.
Procedure1
When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction to your finger.
| Active Test Display |
|---|
| Activate the EVAP Purge VSV |
| Data List Display |
|---|
| EVAP Purge VSV |
| GTS Operation | Specified Condition |
|---|---|
| ON | Purge VSV port applies suction to finger |
| OFF | Purge VSV port applies no suction to finger |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
NG
Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>PURGE VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the purge VSV connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D25)Location & Routingewd_type=routing;type=c;code=D25 Click Connector(D25)Engine Compartment>Engine Wire>Purge VSVewd_type=component;type=c;code=D25;pinno=1 |
||
| D25-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Disconnect the purge VSV connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D25,D51)Location & Routingewd_type=routing;type=c,c;code=D25,D51 Click Connector(D25)Engine Compartment>Engine Wire>Purge VSVewd_type=component;type=c;code=D25;pinno=2 Click Connector(D51)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D51;pinno=43 |
||
| D25-2 (EVP1) - D51-43 (PRG) | Always | Below 1 Ω |
| D25-2 (EVP1) or D51-43 (PRG) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.
Procedure1
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI-MAIN NO. 2 Relay |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO. 2 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (EFI-MAIN NO. 2 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG