Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P011011  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground  


DESCRIPTION

A433504E01
1.438,3.063 2.375,3.281 0.938,0.219 10 false Temperature 3.01,2.615 3.302,2.833 0.292,0.219 10 false [°C] 3.01,2.844 3.302,3.063 0.292,0.219 10 false [°F] 1.375,2.625 1.552,2.833 0.177,0.208 10 false 0 0.885,2.625 1.125,2.823 0.24,0.198 10 false -40 1.75,2.635 1.99,2.833 0.24,0.198 10 false 40 2.156,2.635 2.396,2.833 0.24,0.198 10 false 80 2.552,2.635 2.833,2.833 0.281,0.198 10 false 120 1.344,2.833 1.563,3.042 0.219,0.208 10 false 32 1.719,2.854 2,3.063 0.281,0.208 10 false 104 2.125,2.854 2.406,3.063 0.281,0.208 10 false 176 2.552,2.854 2.833,3.063 0.281,0.208 10 false 248 0.885,2.844 1.125,3.042 0.24,0.198 10 false -40 0.125,0.417 0.667,0.646 0.542,0.229 10 false Voltage 0.698,0.417 0.979,0.646 0.281,0.229 10 false [V] 0.094,0.073 3.208,0.323 3.115,0.25 10 false Characteristics of Intake Air Temperature Sensor: 0.781,2.469 0.958,2.677 0.177,0.208 10 false 0 0.667,2.115 0.885,2.323 0.219,0.208 10 false 1.0 0.677,1.729 0.896,1.938 0.219,0.208 10 false 2.0 0.667,1.365 0.885,1.573 0.219,0.208 10 false 3.0 0.677,1 0.896,1.208 0.219,0.208 10 false 4.0 0.677,0.667 0.896,0.875 0.219,0.208 10 false 5.0

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes.

The intake air temperature detected by the inlet air temperature sensor is converted to a voltage value inside the intake airflow meter assembly, and the voltage value is then output to the ECM. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P011011 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P011011 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground The intake air temperature sensor output voltage is below 0.663 V for 0.5 seconds or more (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (mass air flow meter sub-assembly)

·

ECM


Comes on Engine A SAE: P0112

HINT:

When this DTC is output, check the intake air temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Intake Air Temperature Malfunction
P011011 -39°C (-38.2°F) or less
·

Short to ground in THA circuit

·

Short in THA to E2G circuit

·

Open in VCC circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor (mass air flow meter sub-assembly) circuit, illuminate the MIL and stores a DTC.

Example:

If the intake air temperature sensor output voltage is below 0.663 V for 0.5 seconds or more, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 0.5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P011011.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A434308E07
0.365,2.865 0.823,3.063 0.458,0.198 10 false D23 0.365,3.042 2.708,3.469 2.344,0.427 10 false Intake Air Temperature Sensor (Mass Air Flow Meter Sub-assembly) 5.375,3.135 5.833,3.333 0.458,0.198 10 false D51 5.385,3.302 5.844,3.5 0.458,0.198 10 false ECM 1.396,1.042 1.76,1.24 0.365,0.198 10 false VCC 1.385,1.719 1.75,1.917 0.365,0.198 10 false THA 1.396,2.469 1.76,2.667 0.365,0.198 10 false E2G 4.74,0.896 5.188,1.094 0.448,0.198 10 false VCVG 4.729,1.594 5.177,1.792 0.448,0.198 10 false THA 4.74,2.375 5.104,2.573 0.365,0.198 10 false E2G 4.417,0.896 4.656,1.094 0.24,0.198 10 false 78 4.365,1.594 4.625,1.792 0.26,0.198 10 false 102 4.417,2.354 4.635,2.563 0.219,0.208 10 false 79 1.875,0.896 2.115,1.094 0.24,0.198 10 false 4 1.865,1.594 2.104,1.792 0.24,0.198 10 false 1 1.865,2.375 2.104,2.573 0.24,0.198 10 false 2 5.375,1.406 5.948,1.604 0.573,0.198 10 false 2.7 kΩ

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D23)Location & Routing

Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assembly

D23-4 (VCC) - D23-2 (E2G) Ignition switch ON 4.8 to 5.2 V
D23-1 (THA) - D23-2 (E2G) Ignition switch ON 4.8 to 5.2 V



b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D23)Location & Routing

Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assembly

D23-4 (VCC) - D23-1 (THA) Ignition switch ON 2.565 to 2.835 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



NG

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D23,D51)Location & Routing

Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assembly

Click Connector(D51)Engine Compartment>Engine Wire>ECM

D23-4 (VCC) - D51-78 (VCVG) Always Below 1 Ω
D23-1 (THA) or D51-102 (THA) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR