When the ignition switch is turned to ON, auxiliary battery voltage is applied to IGP of the ECM. When the transistor in the MREL circuit operates, current flows from the auxiliary battery to ground through the drive circuit of the EFI-MAIN NO. 1 relay, thus operating the relay which supplies power to the +B and +B2 terminals of the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A53)Location & Routingewd_type=routing;type=c;code=A53 Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A53;pinno=6 |
||
| A53-6 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A53)Location & Routingewd_type=routing;type=c;code=A53 Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A53;pinno=10,6 |
||
| A53-10 (IGP) - A53-6 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the A/F HTR relay, VVT relay, EFI-MAIN NO. 1 relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block.
Remove the A/F HTR relay, VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A53)Location & Routingewd_type=routing;type=c;code=A53 Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A53;pinno=11,2,3 |
||
| 1 (EFI-MAIN NO. 1 relay) - A53-11 (MREL) | Always | Below 1 Ω |
| 3 (EFI-MAIN NO. 1 relay) - A53-2 (+B) | Always | Below 1 Ω |
| 3 (EFI-MAIN NO. 1 relay) - A53-3 (+B2) | Always | Below 1 Ω |
| 1 (EFI-MAIN NO. 1 relay) or A53-11 (MREL) - Body ground and other terminals | Always | 10 kΩ or higher |
| 3 (EFI-MAIN NO. 1 relay), A53-2 (+B) or A53-3 (+B2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | EFI-MAIN NO. 1 Relay |
Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO. 1 relay) - Body ground | Always | 11 to 14 V |
| 2 (EFI-MAIN NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGP relay from the No. 1 engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A53)Location & Routingewd_type=routing;type=c;code=A53 Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A53;pinno=10 |
||
| 5 (IGP relay) - A53-10 (IGP) | Always | Below 1 Ω |
| 5 (IGP relay) or A53-10 (IGP) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | IGP Relay |
Remove the IGP relay from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IGP relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | IGP Relay |
Remove the IGP relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (IGP relay) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the certification ECU (smart key ECU assembly) connector.
Remove the IGP relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H45)Location & Routingewd_type=routing;type=c;code=H45 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=24 |
||
| H45-24 (IGPD) - 1 (IGP relay) | Always | Below 1 Ω |
| H45-24 (IGPD) or 1 (IGP relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (STARTING)>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Remove the IGP relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H54)Location & Routingewd_type=routing;type=c;code=H54 Click Connector(H54)Instrument Panel>Instrument Panel Wire / Speaker Wire>Ignition Or Starter Switch Assemblyewd_type=component;type=c;code=H54;pinno=8 |
||
| H54-8 (IG1) - 1 (IGP relay) | Always | Below 1 Ω |
| H54-8 (IG1) or 1 (IGP relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG