Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442967 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P008B00  Low Pressure Fuel System Pressure - Too High  


DESCRIPTION

Refer to DTC P008A00.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P008A00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P008B00 Low Pressure Fuel System Pressure - Too High The actual fuel pressure value is higher than target fuel pressure by a certain amount or more (1 trip detection logic).
·

Fuel pump control ECU

·

Fuel pressure sensor

·

ECM


Does not come on Engine B SAE Code: P008B

MONITOR DESCRIPTION

If the fuel pressure increases despite a decrease request signal being sent to the fuel pump control ECU by the ECM, the ECM will store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A333609E54
4.781,0.917 5.031,0.5 5.031,0.5 5.198,0.5 false 5.25,0.427 7.104,0.927 1.854,0.5 10 false There is no designated vehicle speed [Engine running] 0.896,0.521 1.875,0.729 0.979,0.208 10 false Vehicle Speed 1.479,2.177 1.906,2.438 0.427,0.26 10 false Idling 0.688,2.469 2.083,2.688 1.396,0.219 10 false Ignition Switch ON 2.594,3.01 3.406,3.375 0.813,0.365 10 false Warming up 3.823,3.031 5.052,3.25 1.229,0.219 10 false 15 minutes or more 2.219,2.344 2.677,2.542 0.458,0.198 10 false [A] 2.927,2.063 3.385,2.26 0.458,0.198 10 false [B] 4.313,0.688 4.771,0.885 0.458,0.198 10 false [C] 5.323,3.427 5.781,3.625 0.458,0.198 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

10.

With the engine running, drive the vehicle for 15 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P008B00.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [D] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008B00)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P008B00 and other DTCs are output A
P008B00 is output B


HINT:

If any DTCs other than P008B00 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.READ VALUE USING GTS (LOW FUEL PRESSURE SENSOR)
2.READ VALUE USING GTS (LOW FUEL PRESSURE SENSOR)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine.


Procedure1

a.

Record the Low Fuel Pressure Sensor value.

Powertrain > Engine > Data List
Tester Display
Low Fuel Pressure Sensor
50003 372 545
Result:
Proceed to
NEXT



Post-procedure1

a.

None.



NEXT

3.READ VALUE USING GTS (LOW FUEL PRESSURE SENSOR)
3.READ VALUE USING GTS (LOW FUEL PRESSURE SENSOR)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Discharge the fuel pressure.

HINT:

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.


i.

Remove the EFI-MAIN NO. 2 fuse from the No. 1 engine room relay block.


ii.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

iii.

Start the engine.


iv.

After the engine has stopped on its own, turn the ignition switch off.


v.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

vi.

Crank the engine again and make sure that the engine does not start.


vii.

Install the EFI-MAIN NO. 2 fuse.



Procedure1

a.

Read the Data List.

Powertrain > Engine > Data List
Tester Display
Low Fuel Pressure Sensor
50003 372 545

b.

Compare the Low Fuel Pressure Sensor value recorded with the engine running with the Low Fuel Pressure Sensor value currently shown on the GTS.

Result:
Result Proceed to
Low Fuel Pressure Sensor value drops A
Low Fuel Pressure Sensor value is maintained B



Post-procedure1

a.

None.



A

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)

B

REPLACE FUEL PRESSURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PRESSURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



4.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)

Pre-procedure1

a.

Install the fuel pressure gauge.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION



Procedure1

a.

Compare the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.

Powertrain > Engine > Active Test
Active Test Display
Control the Fuel Pump Duty Ratio
Data List Display
Fuel Pump Control Duty Ratio
Low Fuel Pressure Sensor
50004 372 39 101,545
Standard:
GTS Operation Standard
Low Data List value and fuel pressure gauge value are within +/-50 kPa of each other
High


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)

NG

REPLACE FUEL PRESSURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PRESSURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



5.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)

Pre-procedure1

a.

Install the fuel pressure gauge.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION



Procedure1

a.

Read the values on the Data List and the fuel pressure gauge when the Active Test was performed.

Powertrain > Engine > Active Test
Active Test Display
Control the Fuel Pump Duty Ratio
Data List Display
Fuel Pump Control Duty Ratio
Low Fuel Pressure Sensor
50004 372 39 101,545
Result:
GTS Operation Low Fuel Pressure Sensor Fuel Pressure Gauge Proceed to
Low Below 600 kPag Below 600 kPa (6.1 kgf/cm2, 87 psi) A
600 kPag or higher 600 kPa (6.1 kgf/cm2, 87 psi) or higher B



Post-procedure1

a.

None.



A

6.CLEAR DTC

B

REPLACE FUEL PUMP CONTROL ECU

6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P008B00)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P008B00)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Perform All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

b.

Input the DTC: P008B00.


c.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P008B00 is output)
B



Post-procedure1

a.

None.



A

B