1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
Check fuel pump operation.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
2.CHECK FUEL PRESSURE
Discharge fuel system pressure.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
Measure the auxiliary battery voltage.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) auxiliary battery terminal - Negative (-) auxiliary battry terminal | Power switch off | 11 to 14 V |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
|
Open |
|
Pull |
Open the cover of the EFI fuel pipe clamp and remove the EFI fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
| *1 | Fuel Tube Sub-assembly (Vehicle Side) |
| *a | SST (Hose Band) |
| *b | SST (T-joint) |
| *c | SST (Gauge) |
| *d | SST (Hose Joint) |
| *e | SST (Hose) |
| *f | SST (Fuel Tube Connector) |
| *g | Fuel Pipe (Vehicle Side) |
Install SST (EFI fuel pressure gauge) as shown in the illustration.
Wipe up any spilled fuel.
Connect the cable to the negative (-) auxiliary battery terminal.
Initialization after reconnecting auxiliary battery terminal.
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
Measure the fuel pressure.
| Item | Specified Condition |
|---|---|
| Fuel pressure | 284 to 664 kPa |
| Fuel pressure | 2.9 to 6.8 kgf/cm2 |
| Fuel pressure | 41 to 96 psi |
If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump, fuel filter and fuel main valve assembly.
If the result is not as specified, replace the fuel main valve assembly.
Disconnect the GTS from the DLC3.
Start the engine.
Measure the fuel pressure at idle.
| Item | Specified Condition |
|---|---|
| Fuel pressure | 284 to 664 kPa |
| Fuel pressure | 2.9 to 6.8 kgf/cm2 |
| Fuel pressure | 41 to 96 psi |
Refer to Standard Idle Speed.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
Stop the engine.
Check that the fuel pressure remains as specified for 5 minutes.
| Item | Condition | Specified Condition |
|---|---|---|
| Fuel pressure | 5 minutes | 98 kPa or higher |
| Fuel pressure | 5 minutes | 1.0 kgf/cm2 or higher |
| Fuel pressure | 5 minutes | 14.2 psi or higher |
If the result is not as specified, check the fuel pump, fuel main valve assembly and/or port fuel injector assemblies.
After checking the fuel pressure, disconnect the cable from the negative (-) auxiliary battery terminal and carefully remove SST to prevent fuel from spraying.
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
Install the EFI fuel pipe clamp to the fuel tube connector and close the cover of the EFI fuel pipe clamp.
Inspect for fuel leaks.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION