Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442967 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P26CA14  Engine Coolant Pump Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P26CA12.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P26CA12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P26CA14 Engine Coolant Pump Circuit Short to Ground or Open The operation duty ratio (WPO) of the monitoring engine water pump assembly becomes a certain amount or less when engine water pump assembly operation command is output (1 trip detection logic).
·

Open or short in engine water pump assembly (water inlet housing) circuit

·

Engine water pump assembly (water inlet housing)

·

ECM


Comes on Engine A SAE Code: P26CC

Related Data List
DTC No. Data List
P26CA14
·

Coolant Temperature

·

Electric Water Pump Target Speed

·

Electric Water Pump Speed



MONITOR DESCRIPTION

The ECM outputs an operation duty signal (WPO) to steplessly control the speed of the engine water pump assembly. The ECM outputs an operation duty signal (WPO) to the engine water pump assembly and monitors the actual duty signal (WPO) being output. When the operation duty signal (WPO) is being output to the engine water pump assembly and the actual operation duty signal (WPO) is a certain value or less, the ECM detects a malfunction and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Engine water pump assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and maintain the engine speed at 2500 rpm or more for at least 40 seconds [B].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P26CA14.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ECM (INTERNAL CIRCUIT)

Pre-procedure1

a.

Disconnect the engine water pump assembly (water inlet housing) connector.


Procedure1

a.

Measure the resistance while maintaining at 3000 rpm.

Powertrain > Engine > Active Test
Active Test Display
Activate the Electric Water Pump
Data List Display
Electric Water Pump
50004 372 42 437
Standard:
Tester Connection Condition Specified Condition

Click Location & Routing(D34)Location & Routing

Click Connector(D34)Engine Compartment>Engine Wire>Water Inlet with Water Pump Housing Sub-Assembly

D34-3 (SWP) - Body ground During Active Test Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the SWP terminal will be unstable during the Active Test. If the resistance fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING) - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING) - ECM)

Pre-procedure1

a.

Disconnect the engine water pump assembly (water inlet housing) connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D34,D52)Location & Routing

Click Connector(D34)Engine Compartment>Engine Wire>Water Inlet with Water Pump Housing Sub-Assembly

Click Connector(D52)Engine Compartment>Engine Wire>ECM

D34-3 (SWP) - D52-69 (WPO) Always Below 1 Ω
D34-3 (SWP) or D52-69 (WPO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR