Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442967 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P013001  O2 (A/F) Sensor Circuit Bank 1 Sensor 1 General Electrical Failure  P22371B  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold  


DESCRIPTION

The air fuel ratio sensor (sensor 1) is constructed of 2 zirconia cells (VS cell and IP cell), a detection chamber and a heater. It detects fuel injection volume control feedback and three-way catalyst deterioration by detecting the oxygen concentration level in the exhaust gas.

The ECM compares the VS cell voltage and target voltage (0.45 V) and outputs the Ip current for averaging the oxygen concentration level in the detection chamber.

·

The VS cell operates through sufficient heat and current being supplied, and a potential difference is created based on the difference in oxygen ion concentration level between the standard oxygen electrode (Platinum Electrode) and detection chamber.

·

The IP cell controls the oxygen concentration level of the detection chamber.

If the Ip current is positive, the oxygen ions in the detection chamber are sent out. If the Ip current is negative, they are sent in.

·

The detection chamber is between the VS cell and IP cell.

·

The heater heats the zirconia element through the alumina to activate the air fuel ratio sensor (sensor 1).


If the exhaust gas is at the stoichiometric air-fuel ratio, the Ip current will be 0 mA and the VS cell will be at 0.45 V.

If the exhaust gas is rich, the ECM generates a negative Ip current in order to increase the oxygen concentration level in the detection chamber.

If the exhaust gas is lean, the ECM generates a positive Ip current in order to decrease the oxygen concentration level in the detection chamber.

A462677C01
0.823,2.448 1.24,2.031 true 1.344,2 1.729,2.448 true 2.469,2.271 2.74,1.688 true 2.26,2.281 2.469,2.281 2.469,2.281 2.813,1.885 true 2.365,1.5 2.5,1.5 2.5,1.5 2.813,1.26 true 4.354,1.781 4.208,1.781 4.208,1.781 3.896,1.49 true 4.365,0.729 4.219,0.729 4.219,0.729 3.896,1.052 true 4.292,2.125 4.135,2.125 4.135,2.125 3.542,1.604 true 4.115,2.104 3.521,1.354 true 2.979,1.156 2.49,0.531 2.49,0.531 2.333,0.531 true 2.958,0.927 2.49,0.521 true 2.792,2.604 3,2.604 3,2.604 3.635,1.896 true 2.99,2.594 3.063,1.906 true 0.438,2.125 0.75,2.323 0.313,0.198 10 false *1 0.656,2.396 0.969,2.594 0.313,0.198 10 false *2 1.802,2.427 2.115,2.625 0.313,0.198 10 false *3 2.135,0.479 2.448,0.677 0.313,0.198 10 false *4 2.073,2.229 2.385,2.427 0.313,0.198 10 false *5 3.24,0.5 3.552,0.698 0.313,0.198 10 false *6 2.615,2.552 2.927,2.75 0.313,0.198 10 false *7 4.427,0.677 4.74,0.875 0.313,0.198 10 false *8 4.417,1.719 4.729,1.917 0.313,0.198 10 false *9 4.354,2.094 4.667,2.292 0.313,0.198 10 false *4 2.198,1.448 2.51,1.646 0.313,0.198 10 false *1
*1 Exhaust gas *2 Cover
*3 Element *4 Platinum Electrode
*5 Alumina *6 Element Cross Sectional Diagram
*7 Heater *8 Zirconia (IP cell)
*9 Zirconia (VS cell) - -


DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P013001 O2 (A/F) Sensor Circuit Bank 1 Sensor 1 General Electrical Failure Refer to the chart below (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on Engine A SAE Code: P0130
P22371B A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold The air fuel ratio sensor (sensor 1) impedance is higher than 185.209 Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on Engine A SAE Code: P2238

P013001 Detection Conditions Malfunction Condition
VS+ Low COM Low IP+ Low VS+ High COM High IP+ High
Diagnosis Condition Auxiliary battery voltage 10.5 V or higher ○ ○ ○ ○ ○ ○
5 seconds or more after turning the ignition switch to ON ○ ○ ○ ○ ○ ○
Malfunction Status VS+ terminal voltage below 0.3 V ○ - - - - -
COM terminal voltage below 0.3 V - ○ - - - -
IP+ terminal voltage below 0.3 V - - ○ - - -
Short in VS+ terminal circuit to power source circuit - - - ○ - -
Short in COM terminal circuit to power source circuit - - - - ○ -
Short in IP+ terminal circuit to power source circuit - - - - - ○
Malfunction Duration 5 seconds or more 5 seconds or more 5 seconds or more 5 seconds or more 5 seconds or more 5 seconds or more

P013001 Detection Conditions Malfunction Condition
Short in either VS+ or COM Open circuit in VS+ Open circuit in IP+ Open circuit in COM
Diagnosis Condition Auxiliary battery voltage 10.5 V or higher ○ ○ ○ ○
5 seconds or more after turning the ignition switch to ON ○ ○ ○ ○
Air fuel ratio sensor (sensor 1) impedance smaller than 100 Ω ○ - - -
Air fuel ratio sensor (sensor 1) heater duty 20% or higher for 10 seconds or more - ○ - -
Air fuel ratio sensor (sensor 1) impedance smaller than 400 Ω - - ○ ○
Malfunction Status Difference between VS+ terminal voltage and COM terminal voltage below 0.2 V ○ - - -
VS+ terminal voltage exceeds 4.6 V - ○ - -
Difference between COM sweep current (sink) and COM sweep current (source ) is 0.4 mA or higher - - ○ -
COM terminal voltage is below 2.3 V or exceeds 2.7 V - - - ○
Malfunction Duration 5 seconds or more 5 seconds or more 5 seconds or more 5 seconds or more

MONITOR DESCRIPTION

These DTCs are stored when there is an open or short in the air fuel ratio sensor (sensor 1) circuit, or the air fuel ratio sensor (sensor 1) output value is abnormal. The voltage or current of the air fuel ratio sensor (sensor 1) is monitored while the ignition switch is ON or the engine is running, and the impedance (impedance is an electrical term that indicates the difficulty of flow of current) is checked while engine running. If the voltage or current of the air fuel ratio sensor (sensor 1) is outside the normal range, or the impedance is outside the normal range, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor (sensor 1)
Required Sensors/Components (Related) Engine coolant temperature sensor
Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine.

10.

Wait 5 minutes.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes.

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P013001 or P22371B.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1].

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D40)Location & Routing

Click Connector(D40)Engine Compartment>Engine Wire>Air Fuel Ratio Sensor

D40-1 (IP+) - Body ground Ignition switch ON 2.4 to 2.6 V
D40-2 (COM) - Body ground Ignition switch ON 2.4 to 2.6 V
D40-3 (VS+) - Body ground Ignition switch ON 4.1 to 5.0 V
D40-1 (IP+) - D40-2 (COM) Ignition switch ON -0.2 to 0.2 V
D40-3 (VS+) - D40-2 (COM) Ignition switch ON 1.7 to 2.6 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))

Pre-procedure1

a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D40,D52)Location & Routing

Click Connector(D40)Engine Compartment>Engine Wire>Air Fuel Ratio Sensor

Click Connector(D52)Engine Compartment>Engine Wire>ECM

D40-4 (HA1A) - D52-28 (HA1A) Always Below 1 Ω
D40-1 (IP+) - D52-100 (IP+) Always Below 1 Ω
D40-2 (COM) - D52-99 (COM) Always Below 1 Ω
D40-3 (VS+) - D52-98 (VS+) Always Below 1 Ω
D40-4 (HA1A) or D52-28 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
D40-1 (IP+) or D52-100 (IP+) - Body ground and other terminals Always 10 kΩ or higher
D40-2 (COM) or D52-99 (COM) - Body ground and other terminals Always 10 kΩ or higher
D40-3 (VS+) or D52-98 (VS+) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR