Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442967 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P003012  HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery  P003013  HO2S Heater Control Bank 1 Sensor 1 Circuit Open  P101A9E  A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On  


DESCRIPTION

Refer to DTC P013001.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P013001

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor (sensor 1) heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor (sensor 1).

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor (sensor 1) heater circuit uses a relay on the +B side of the circuit.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P003012 HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery The air fuel ratio sensor (sensor 1) heater current is more than the specified value while the heater is operating (1 trip detection logic).
·

Short in air fuel ratio sensor (sensor 1) heater circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on Engine A SAE Code: P0032
P003013 HO2S Heater Control Bank 1 Sensor 1 Circuit Open The air fuel ratio sensor (sensor 1) heater current is less than the specified value while the heater is operating (1 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) heater circuit

·

Air fuel ratio sensor (sensor 1)

·

A/F HTR relay

·

ECM


Comes on Engine A SAE Code: P0031
P101A9E A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On The air fuel ratio sensor (sensor 1) heater voltage level is low while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (sensor 1) heater circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on Engine A SAE Code: P101D

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor (sensor 1) to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor (sensor 1) detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor (sensor 1) is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful current signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor (sensor 1) becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor (sensor 1) heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P003012
Output duty cycle 10% or higher

P003013
Output duty cycle 30% or higher

P101A9E
Output duty cycle Less than 75%

CONFIRMATION DRIVING PATTERN

A262623E89
0.75,0.969 1.396,1.167 0.646,0.198 10 false 2500 rpm 0.979,1.74 1.385,1.979 0.406,0.24 10 false Idling 0.427,2.021 1.323,2.396 0.896,0.375 10 false Ignition Switch ON 1.927,2.135 2.208,2.354 0.281,0.219 10 false [A] 2.76,1.625 3.115,1.938 0.354,0.313 10 false [B] 4.021,0.865 4.344,1.156 0.323,0.292 10 false [C] 5.385,1.604 5.729,1.906 0.344,0.302 10 false [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 false 5 minutes or more 3.854,2.615 4.427,2.781 0.573,0.167 10 false 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and idle it for 5 minutes or more [B].

10.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 2500 rpm for 1 minute [C].

HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform steps [C] and [D] after charge control has completed.


11.

Idle the engine for 5 minutes or more [D].

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P003012, P003013 or P101A9E.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [E] again.




WIRING DIAGRAM

A459400E01
0.771,5.698 1.938,6.052 1.167,0.354 10 false Auxiliary Battery 0.594,4.208 1.438,4.417 0.844,0.208 10 false BATT-MAIN 0.708,3.281 1.344,3.688 0.635,0.406 10 false EFI-MAIN NO. 1 1.563,3.719 2.781,4.063 1.219,0.344 10 false EFI-MAIN NO. 1 1.604,3.26 1.76,3.458 0.156,0.198 10 false 2 1.594,2.948 1.75,3.146 0.156,0.198 10 false 5 2.438,2.969 2.594,3.167 0.156,0.198 10 false 3 2.427,3.24 2.583,3.438 0.156,0.198 10 false 1 5.396,3.365 5.854,3.563 0.458,0.198 10 false A53 5.438,3.167 5.75,3.365 0.313,0.198 10 false 11 6.125,4.823 6.583,5.021 0.458,0.198 10 false ECM 3.729,5.115 5.083,5.521 1.354,0.406 10 false *: Shielded 6.5,2.292 6.813,2.49 0.313,0.198 10 false IC 1.615,2.177 2.365,2.469 0.75,0.292 10 false EFI NO. 3 1.615,0.458 1.771,0.656 0.156,0.198 10 false 3 1.615,0.74 1.771,0.938 0.156,0.198 10 false 1 2.406,0.448 2.563,0.646 0.156,0.198 10 false 5 2.396,0.75 2.552,0.948 0.156,0.198 10 false 2 1.781,1.177 2.427,1.406 0.646,0.229 10 false A/F HTR 3.604,0.458 3.76,0.656 0.156,0.198 10 false 5 3.802,0.448 4.115,0.646 0.313,0.198 10 false +B 4.635,1.698 4.792,1.896 0.156,0.198 10 false 2 4.208,1.677 4.823,1.875 0.615,0.198 10 false COM 4.177,0.448 4.792,0.646 0.615,0.198 10 false HA1A 4.646,0.427 4.802,0.625 0.156,0.198 10 false 4 4.313,1.229 4.927,1.427 0.615,0.198 10 false IP+ 4.646,2.156 4.802,2.354 0.156,0.198 10 false 3 3.385,2.656 3.844,2.854 0.458,0.198 10 false D40 3.385,2.833 4.729,3.365 1.344,0.531 10 false Air Fuel Ratio Sensor (Sensor 1) 5.417,1.802 6.031,2 0.615,0.198 10 false D52 5.448,2.115 5.76,2.313 0.313,0.198 10 false 98 5.063,2.625 5.219,2.823 0.156,0.198 10 false * 5.74,3.219 6.354,3.417 0.615,0.198 10 false MREL 5.406,1.146 5.719,1.344 0.313,0.198 10 false 100 5.719,0.448 6.333,0.646 0.615,0.198 10 false HA1A 5.448,0.385 5.667,0.625 0.219,0.24 10 false 28 0.844,0.708 1.49,0.938 0.646,0.229 10 false A/F HTR 4.625,1.188 4.781,1.385 0.156,0.198 10 false 1 4.25,2.188 4.865,2.385 0.615,0.198 10 false VS+ 5.406,2.292 6.021,2.49 0.615,0.198 10 false D52 5.458,1.615 5.771,1.813 0.313,0.198 10 false 99 5.729,2.167 6.344,2.365 0.615,0.198 10 false VS+ 5.729,1.688 6.344,1.885 0.615,0.198 10 false COM 5.74,1.229 6.354,1.427 0.615,0.198 10 false IP+ 5.417,1.333 6.031,1.531 0.615,0.198 10 false D52 5.406,0.563 6.021,0.76 0.615,0.198 10 false D52

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

Refer to "Data List / Active Test" [A/F (O2) Sensor Heater Duty Ratio B1S1].

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor (sensor 1) output current (Click here Engine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P013616). If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (SENSOR 1) (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))

NG

REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))

Pre-procedure1

a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D40)Location & Routing

Click Connector(D40)Engine Compartment>Engine Wire>Air Fuel Ratio Sensor

D40-5 (+B) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)

NG

6.INSPECT A/F HTR RELAY
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)

Pre-procedure1

a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D40,D52)Location & Routing

Click Connector(D40)Engine Compartment>Engine Wire>Air Fuel Ratio Sensor

Click Connector(D52)Engine Compartment>Engine Wire>ECM

D40-4 (HA1A) - D52-28 (HA1A) Always Below 1 Ω
D40-4 (HA1A) or D52-28 (HA1A) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013 AND/OR P101A9E)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013 AND/OR P101A9E)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P003012, P003013 or P101A9E is output B



Post-procedure1

a.

None.



A

B

6.INSPECT A/F HTR RELAY

OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F HTR RELAY)

NG

REPLACE A/F HTR RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F HTR RELAY)

Pre-procedure1

a.

Remove the A/F HTR relay from the No. 1 engine room relay block.


Procedure1

a.
A459243C01
0.25,1.021 0.563,1.177 0.313,0.156 10 false *1 0.885,0.104 1.198,0.26 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 A/F HTR Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (A/F HTR relay) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

8.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - A/F HTR RELAY)

8.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - BODY GROUND)

Pre-procedure1

a.

Remove the A/F HTR relay from the No. 1 engine room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (A/F HTR relay) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

9.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - AIR FUEL RATIO SENSOR (SENSOR 1))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - AIR FUEL RATIO SENSOR (SENSOR 1))

Pre-procedure1

a.

Remove the A/F HTR relay from the No. 1 engine room relay block.


b.

Disconnect the air fuel ratio sensor (sensor 1) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D40)Location & Routing

Click Connector(D40)Engine Compartment>Engine Wire>Air Fuel Ratio Sensor

5 (A/F HTR relay) - D40-5 (+B) Always Below 1 Ω
5 (A/F HTR relay) or D40-5 (+B) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - A/F HTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR