The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the fuel injector connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E1,E2,E3)Location & Routingewd_type=routing;type=c,c,c;code=E1,E2,E3 Click Connector(E1)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 1ewd_type=component;type=c;code=E1;pinno=1 Click Connector(E2)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 2ewd_type=component;type=c;code=E2;pinno=1 Click Connector(E3)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 3ewd_type=component;type=c;code=E3;pinno=1 |
||
| E1-1 (#1) - Body ground | Ignition switch ON | 11 to 14 V |
| E2-1 (#2) - Body ground | Ignition switch ON | 11 to 14 V |
| E3-1 (#3) - Body ground | Ignition switch ON | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Disconnect the fuel injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E1,D52,E2,E3)Location & Routingewd_type=routing;type=c,c,c,c;code=E1,D52,E2,E3 Click Connector(E1)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 1ewd_type=component;type=c;code=E1;pinno=2 Click Connector(D52)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D52;pinno=96,95,94 Click Connector(E2)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 2ewd_type=component;type=c;code=E2;pinno=2 Click Connector(E3)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 3ewd_type=component;type=c;code=E3;pinno=2 |
||
| E1-2 (#10) - D52-96 (#10) | Always | Below 1 Ω |
| E2-2 (#20) - D52-95 (#20) | Always | Below 1 Ω |
| E3-2 (#30) - D52-94 (#30) | Always | Below 1 Ω |
| E1-2 (#10) or D52-96 (#10) - Body ground and other terminals | Always | 10 kΩ or higher |
| E2-2 (#20) or D52-95 (#20) - Body ground and other terminals | Always | 10 kΩ or higher |
| E3-2 (#30) or D52-94 (#30) - Body ground and other terminals | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the IGP relay from the No. 1 engine room relay block.
Disconnect the fuel injector assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E1,E2,E3)Location & Routingewd_type=routing;type=c,c,c;code=E1,E2,E3 Click Connector(E1)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 1ewd_type=component;type=c;code=E1;pinno=1 Click Connector(E2)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 2ewd_type=component;type=c;code=E2;pinno=1 Click Connector(E3)Engine Compartment>No. 5 Engine Wire>Fuel Injector Assembly No. 3ewd_type=component;type=c;code=E3;pinno=1 |
||
| 5 (IGP relay) - E1-1 (#1) | Always | Below 1 Ω |
| 5 (IGP relay) - E2-1 (#2) | Always | Below 1 Ω |
| 5 (IGP relay) - E3-1 (#3) | Always | Below 1 Ω |
| 5 (IGP relay) or E1-1 (#1) - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGP relay) or E2-1 (#2) - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGP relay) or E3-1 (#3) - Body ground and other terminals | Always | 10 kΩ or higher |
If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.
| Result |
|---|
| OK |
| NG |
OK
NG