Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443935 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B596988N02
6.5,0.271 6.833,0.271 false 6.417,0.563 6.75,0.563 false 5.771,3.313 5.771,2.979 false 6.438,0.875 6.771,0.875 false 6.208,0.427 6.49,0.781 0.281,0.354 18 false 6 5.656,0.135 6.604,0.448 0.948,0.313 18 false 3, 4, 5 5.813,3.313 6.094,3.667 0.281,0.354 18 false 1 6.229,0.74 6.51,1.094 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HORN BUTTON ASSEMBLY 45130 (Click here) - -
2 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 INSPECT HORN BUTTON ASSEMBLY - (Click here) - -
4 PERFORM DIAGNOSTIC SYSTEM CHECK - (Click here) -
5 INSPECT SRS WARNING LIGHT - (Click here) - -
6 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

PROCEDURE

Hide 45130 1.INSTALL HORN BUTTON ASSEMBLY

a.
B596997C01
1.677,0.802 0.677,0.802 true 0.5,0.708 0.813,0.865 0.313,0.156 10 false *a 4.615,0.104 4.896,0.458 0.281,0.354 18 false ii 0.167,0.094 0.448,0.448 0.281,0.354 18 false i 0.354,1.771 0.729,2.01 0.375,0.24 12 false *A 2.729,1.813 3.104,2.052 0.375,0.24 12 false *B
*A w/ Smart Entry and Start System *B w/o Smart Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592964N01
2.292,1.427 2.573,1.781 0.281,0.354 18 false i 1.448,0.854 1.729,1.208 0.281,0.354 18 false ii 2.01,0.917 2.292,1.271 0.281,0.354 18 false iii 4.917,0.625 5.198,0.979 0.281,0.354 18 false vi 6.104,0.615 6.385,0.969 0.281,0.354 18 false vi 5.583,1.354 5.865,1.708 0.281,0.354 18 false vii 4.24,0.063 4.521,0.417 0.281,0.354 18 false v 1.323,1.094 1.604,1.448 0.281,0.354 18 false iv

i.

Support the button assembly with one hand.


ii.

Connect the horn connector.


iii.

Engage the wire harness clamp.


iv.

Connect the airbag connector.

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Be sure to connect the connectors to each corresponding color.

·

Make sure the lock button is securely locked.



HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



v.

Set the horn button assembly to the steering wheel assembly.

NOTICE:

Check that the airbag wire harness and horn wire harness are not pinched.



vi.

Press the horn button assembly with both hands to engage the upper pin to the upper spring.


vii.

Press the horn button assembly with both hands to engage the lower pin to the lower spring.

NOTICE:

After installation, try to pull the horn button assembly and check that the horn button assembly is securely installed.




Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 45130 3.INSPECT HORN BUTTON ASSEMBLY

a.

Make sure that the horn sounds.

If the horn does not sound, inspect the horn system.

Click hereVehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE


Hide 5.INSPECT SRS WARNING LIGHT

Z101186

Click here(Click here)

Hide 6. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART