| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | SIDE NO. 1 AIRBAG SENSOR | 89831 | ( )
|
- | - |
| 2 | FRONT SEAT OUTER BELT ASSEMBLY | 73210 | ( )
|
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *A | for Gasoline Model | *B | for HV Model |
| *C | for LH Side | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
Use the same procedure for the RH side and LH side.
The following procedure is for the RH side.
89831
1.INSTALL SIDE NO.1 AIR BAG SENSOR
| *A | w/ Smart Entry and Start System | *B | w/o Smart Entry and Start System |
| *a | Illumination off | - | - |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Engage the guide to hold the side No. 1 airbag sensor in place.
If the side No. 1 airbag sensor has been dropped, replace it with a new one.
Install the bolt.
When installing the side No. 1 airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
Tighten the bolt while holding the side No. 1 airbag sensor because the side No. 1 airbag sensor guide is easily damaged.
Check that there is no looseness in the installation parts of the side No. 1 airbag sensor.
Connect the airbag connector.
When connecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
73210
2.INSTALL FRONT SEAT OUTER BELT ASSEMBLY
| *A | w/ Smart Entry and Start System | *B | w/o Smart Entry and Start System |
| *a | Illumination off | - | - |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Engage the guides to temporarily install the front seat outer belt assembly.
Temporarily install the 2 bolts.
Tighten bolt (A) and then bolt (B).
Connect the pretensioner connector.
Refer to How to Connect or Disconnect Airbag Connector:
62413A
3.INSTALL CENTER PILLAR LOWER GARNISH
73210
4.CONNECT FRONT SEAT OUTER BELT ASSEMBLY
73233
5.INSTALL LAP BELT OUTER ANCHOR COVER
62311B
6.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
67913B
7.INSTALL FRONT DOOR SCUFF PLATE
62331A
8.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
67917F
9.INSTALL REAR DOOR SCUFF PLATE
76973F
10.INSTALL REAR UNDER SIDE COVER (for HV Model)
11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
12. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART