Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441184 MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P31481F  Lost Communication between Drive Motor "A" and "B" Circuit Intermittent  P314887  Lost Communication between Drive Motor "A" and "B" Missing Message  


DESCRIPTION

The motor generator control ECU (MG ECU) built into the hybrid motor control inverter assembly communicates with the rear motor generator control ECU.

The motor generator control ECU monitors communication data and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P31481F Lost Communication between Drive Motor "A" and "B" Circuit Intermittent Communication interrupted between motor generator control ECU and rear motor generator control ECU
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid motor control inverter assembly

·

Rear inverter assembly

·

PCU FR fuse


Does not come on Master Warning:
Does not come on
Motor Generator A
P314887 Lost Communication between Drive Motor "A" and "B" Missing Message Communication interrupted between motor generator control ECU and rear motor generator control ECU
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid motor control inverter assembly

·

Rear inverter assembly

·

PCU FR fuse


Does not come on Master Warning:
Comes on
Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




WIRING DIAGRAM

A459261E11
0.99,2.938 1.604,3.135 0.615,0.198 10 false +BR1 0.99,3.292 1.604,3.49 0.615,0.198 10 false +BR2 1,3.792 1.615,3.99 0.615,0.198 10 false GNR1 0.99,4.125 1.604,4.323 0.615,0.198 10 false GNR2 0.708,3.167 1.021,3.365 0.313,0.198 10 false 13 0.781,2.823 1.125,3.031 0.344,0.208 10 false 6 0.781,3.667 1.125,3.865 0.344,0.198 10 false 1 0.781,4.021 1.208,4.208 0.427,0.188 10 false 7 1.948,3.406 2.104,3.604 0.156,0.198 10 false * 2.313,3.052 2.927,3.25 0.615,0.198 10 false CARH 4.458,3.042 5.073,3.24 0.615,0.198 10 false CARH 2.333,3.521 2.948,3.719 0.615,0.198 10 false CARL 4.469,3.531 5.083,3.729 0.615,0.198 10 false CARL 5.146,3.385 5.302,3.583 0.156,0.198 10 false * 2.302,4.302 2.917,4.5 0.615,0.198 10 false DRNA 2.813,3.042 3.156,3.25 0.344,0.208 10 false 2 2.823,3.521 3.167,3.729 0.344,0.208 10 false 8 2.833,4.188 3.177,4.396 0.344,0.208 10 false 9 4.24,3.042 4.583,3.25 0.344,0.208 10 false 3 4.24,3.51 4.583,3.719 0.344,0.208 10 false 9 0.635,4.708 1.094,4.906 0.458,0.198 10 false O74 0.646,4.885 3.469,5.219 2.823,0.333 10 false Rear Hybrid Motor Control Inverter Assembly 4.406,4.708 4.865,4.906 0.458,0.198 10 false A56 4.427,4.896 6.885,5.115 2.458,0.219 10 false Hybrid Motor Control Inverter Assembly 0.167,5.458 2.094,5.688 1.927,0.229 10 false *: Approximately 120 Ω 5.979,2.938 6.594,3.135 0.615,0.198 10 false +B 5.896,3.281 6.51,3.479 0.615,0.198 10 false +B2 5.802,3.792 6.417,3.99 0.615,0.198 10 false GND1 5.792,4.135 6.406,4.333 0.615,0.198 10 false GND2 6.26,2.823 6.604,3.031 0.344,0.208 10 false 6 6.281,3.167 6.625,3.375 0.344,0.208 10 false 5 6.281,3.667 6.625,3.875 0.344,0.208 10 false 24 6.292,4.01 6.635,4.219 0.344,0.208 10 false 23 5.865,2.354 6.563,2.542 0.698,0.188 10 false PCU FR 1.833,1.26 2.531,1.448 0.698,0.188 10 false PCU RR 1.74,0.354 1.896,0.552 0.156,0.198 10 false 5 2.354,0.354 2.51,0.552 0.156,0.198 10 false 3 3.25,0.615 3.948,0.802 0.698,0.188 10 false PCU-RR 1.74,0.885 1.896,1.083 0.156,0.198 10 false 1 2.354,0.896 2.51,1.094 0.156,0.198 10 false 2 4.49,1 5.188,1.188 0.698,0.188 10 false MREL 4.438,1.646 6.302,1.969 1.865,0.323 10 false Hybrid Vehicle Control ECU 4.469,1.469 5.167,1.656 0.698,0.188 10 false H44 4.188,0.865 4.5,1.063 0.313,0.198 10 false 47

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C69
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs
50002 395
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

2.CHECK DTC OUTPUT (MOTOR GENERATOR CONTROL)
2.CHECK DTC OUTPUT (MOTOR GENERATOR CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result: Proceed to
P31481F or P314887 is output A
P31481F and P314887 are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

3.INSPECTION FUSE (PCU FR)

B

3.INSPECTION FUSE (PCU FR)

Pre-procedure1

a.
A459953C01
2.177,0.719 2.625,1.083 true 0.208,0.156 0.521,0.313 0.313,0.156 10 false *1 2.594,1.156 2.906,1.313 0.313,0.156 10 false *2
*1 No. 5 Relay Block
*2 PCU FR fuse


Remove the PCU FR fuse from the No. 5 relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Output DTC
PCU FR fuse terminals Always Below 1 Ω P31481F,P314887


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the PCU FR fuse.



OK

4.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)

NG

8.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - FUSE (PCU FR))
4.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


Procedure1

a.
A365593C81
0.292,0.885 0.667,1.146 0.375,0.26 2.031,1.25 2.719,1.833 true 1.906,1.25 1.917,1.833 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.354,0.948 0.813,1.146 0.458,0.198 10 false A56 2.719,1.875 3.177,2.073 0.458,0.198 10 false GND1 1.823,1.865 2.438,2.063 0.615,0.198 10 false GND2
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-24 (GND1) - Body ground Ignition switch off Below 1 Ω P31481F,P314887
A56-23 (GND2) - Body ground Ignition switch off Below 1 Ω P31481F,P314887


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
A365593C82
0.292,0.885 0.667,1.146 0.375,0.26 2.042,0.917 2.604,0.302 true 1.906,0.906 2.094,0.271 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.354,0.948 0.813,1.146 0.458,0.198 10 false A56 2.667,0.208 2.979,0.406 0.313,0.198 10 false +B 2.146,0.135 2.604,0.333 0.458,0.198 10 false +B2
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-6 (+B) - Body ground Ignition switch ON Same as auxiliary battery voltage P31481F,P314887
A56-5 (+B2) - Body ground Ignition switch ON Same as auxiliary battery voltage P31481F,P314887


NOTICE:

Turning the ignition switch to ON with the hybrid motor control inverter assembly connector and ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable to the negative (-) auxiliary battery terminal.


c.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

6.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

6.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


c.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


Procedure1

a.
A378663C30
0.188,3.438 0.594,3.677 0.406,0.24 0.344,1.188 0.75,1.427 0.406,0.24 1.927,0.344 1.625,1.115 true 1.563,1.25 1.219,0.344 true 1.115,2.708 1.365,3.292 true 1.167,4.146 1.333,3.615 true 0.229,0.188 0.542,0.344 0.313,0.156 10 false *a 0.25,2.615 0.563,2.771 0.313,0.156 10 false *b 2,0.24 2.427,0.458 0.427,0.219 10 false CARH 0.427,1.25 0.813,1.438 0.385,0.188 10 false A56 0.25,3.479 0.615,3.646 0.365,0.167 10 false O74 0.823,0.25 1.25,0.469 0.427,0.219 10 false CARL 0.667,2.615 1.094,2.833 0.427,0.219 10 false CARH 0.99,4.188 1.417,4.406 0.427,0.219 10 false CARL
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)
*b Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) - O74-2 (CARH) Ignition switch off Below 1 Ω P31481F,P314887
A56-9 (CARL) - O74-8 (CARL) Ignition switch off Below 1 Ω P31481F,P314887


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) or O74-2 (CARH) - Body ground and other terminals Ignition switch off 10 kΩ or higher P31481F,P314887
A56-9 (CARL) or O74-8 (CARL) - Body ground and other terminals Ignition switch off 10 kΩ or higher P31481F,P314887



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) or O74-2 (CARH) - Body ground Ignition switch ON Below 1 V P31481F,P314887
A56-9 (CARL) or O74-8 (CARL) - Body ground Ignition switch ON Below 1 V P31481F,P314887


NOTICE:

Turning the ignition switch to ON with the hybrid motor control inverter assembly connector and rear hybrid motor control inverter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable to the negative (-) auxiliary battery terminal.


c.

Connect the O74 rear hybrid motor control inverter assembly connector.


d.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

7.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


Procedure1

a.
A365592C87
1,1.792 1.406,2.021 0.406,0.229 1.26,0.865 0.99,0.323 true 1.219,0.99 0.469,0.594 true 1.104,1.833 1.563,2.031 0.458,0.198 10 false A56 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.604,0.219 1.219,0.417 0.615,0.198 10 false CARH 0.104,0.521 0.719,0.719 0.615,0.198 10 false CARL
*a Component without harness connected
(Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-3 (CARH) - A56-9 (CARL) Ignition switch off 80 to 170 Ω P31481F,P314887


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - FUSE (PCU FR))
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A365593C77
0.292,0.979 0.667,1.229 0.375,0.25 2.031,0.906 2.708,0.333 true 1.917,0.896 2.188,0.24 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.354,1.031 0.813,1.229 0.458,0.198 10 false A56 2.771,0.25 3.083,0.448 0.313,0.198 10 false +B 2.24,0.156 2.698,0.354 0.458,0.198 10 false +B2
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)


Disconnect the A56 hybrid motor control inverter assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-6 (+B) - Body ground Ignition switch off 10 kΩ or higher P31481F,P314887
A56-5 (+B2) - Body ground Ignition switch off 10 kΩ or higher P31481F,P314887


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

9.REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NEXT

REPLACE FUSE (PCU FR)

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PCU FR)