Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A3011  Drive Motor "B" Temperature Sensor Circuit Short to Ground  P0A3015  Drive Motor "B" Temperature Sensor Circuit Short to Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the rear motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU malfunction
·

Hybrid vehicle control ECU internal malfunction


Rear motor temperature sensor malfunction
·

Internal rear motor temperature sensor malfunction

·

Open or short in rear motor temperature sensor


Wire harness between the rear motor temperature sensor and hybrid vehicle control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the rear motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the rear motor (MGR) becomes high. If the self-protection function does not operate, the rear motor (MGR) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

The resistance of the thermistor built into the rear motor temperature sensor changes in accordance with changes in the rear motor temperature. The lower the rear motor temperature, the higher the thermistor resistance. Conversely, the higher the rear motor temperature, the lower the resistance.

C189867E17
0.76,2.104 0.885,2.302 0.125,0.198 10 false 0 2,2.875 3.406,3.094 1.406,0.219 10 false Temperature (°C (°F)) 0.885,2.375 1.083,2.573 0.198,0.198 10 false 10 1.26,2.375 1.458,2.573 0.198,0.198 10 false 15 2.406,2.375 2.604,2.573 0.198,0.198 10 false 30 2.792,2.375 2.99,2.573 0.198,0.198 10 false 35 1.646,2.375 1.844,2.573 0.198,0.198 10 false 20 2.021,2.375 2.219,2.573 0.198,0.198 10 false 25 0.677,1.521 0.875,1.719 0.198,0.198 10 false 50 0.594,0.948 0.865,1.146 0.271,0.198 10 false 100 3.146,2.375 3.344,2.573 0.198,0.198 10 false 40 0.063,0.5 1.26,0.771 1.198,0.271 10 false Resistance (kΩ) 0.865,2.542 1.208,2.74 0.344,0.198 10 false (50) 1.229,2.552 1.573,2.75 0.344,0.198 10 false (59) 1.615,2.552 1.958,2.75 0.344,0.198 10 false (68) 1.979,2.563 2.323,2.76 0.344,0.198 10 false (77) 2.385,2.573 2.729,2.771 0.344,0.198 10 false (86) 2.771,2.583 3.115,2.781 0.344,0.198 10 false (95) 3.063,2.583 3.406,2.781 0.344,0.198 10 false (104)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0A3011 Drive Motor "B" Temperature Sensor Circuit Short to Ground Line short or short to ground in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Rear traction motor with transaxle assembly (Rear motor temperature sensor)


Does not come on Master Warning: Comes on Hybrid Control A
P0A3015 Drive Motor "B" Temperature Sensor Circuit Short to Battery or Open Open or short to +B in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Rear traction motor with transaxle assembly (Rear motor temperature sensor)


Does not come on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P0A3011 Rear Motor Temperature
P0A3015

HINT:

After confirming that DTC P0A3611 or P0A3615 is output, use the GTS to check "Rear Motor Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A455944E09
5.25,2.646 5.708,2.844 0.458,0.198 10 false H44 5.25,2.823 7.083,3.271 1.833,0.448 10 false Hybrid Vehicle Control ECU 0.073,2.667 0.385,2.865 0.313,0.198 10 false U1 0.073,2.813 2.208,3.552 2.135,0.74 10 false Rear Traction Motor with Transaxle Assembly (Rear Motor Temperature Sensor) 3.708,2.521 4.167,2.719 0.458,0.198 10 false OH3 2.375,2.51 2.833,2.708 0.458,0.198 10 false UO1 2.375,2.656 3.49,3.063 1.115,0.406 10 false No. 3 Frame Wire Connector 3.719,2.667 5.583,3.156 1.865,0.49 10 false Floor Wire Connector 1.24,1.854 1.854,2.052 0.615,0.198 10 false RMTG 1.333,0.677 1.792,0.875 0.458,0.198 10 false RMT 5.385,0.677 5.844,0.875 0.458,0.198 10 false RMT 5.375,1.865 5.99,2.063 0.615,0.198 10 false RMTG 5.104,1.865 5.417,2.063 0.313,0.198 10 false 53 5.115,0.677 5.427,0.875 0.313,0.198 10 false 54 4.406,0.667 4.719,0.865 0.313,0.198 10 false 2 3.813,0.667 4.125,0.865 0.313,0.198 10 false 2 3.031,0.667 3.188,0.865 0.156,0.198 10 false 2 2.427,0.667 2.583,0.865 0.156,0.198 10 false 2 1.74,0.677 1.896,0.875 0.156,0.198 10 false 2 1.729,1.854 2,2.063 0.271,0.208 10 false 12 2.396,1.854 2.552,2.052 0.156,0.198 10 false 8 3.021,1.854 3.177,2.052 0.156,0.198 10 false 8 3.802,1.854 4.115,2.052 0.313,0.198 10 false 1 4.417,1.854 4.729,2.052 0.313,0.198 10 false 1 6.469,0.771 6.927,0.969 0.458,0.198 10 false ADC

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
a.

Check the connection condition of the floor wire connector and the contact pressure of each terminal. Check the terminal for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FRAME WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FRAME WIRE CONNECTOR)
a.

Check the connection condition of the No. 3 frame wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.READ VALUE USING GTS (REAR MOTOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (REAR MOTOR TEMPERATURE)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
Result:
Result Proceed to
The value of Rear Motor Temperature is -40 °C A
The value of Rear Motor Temperature is 215 °C B
None of the above conditions are met C


HINT:
·

-40°C (-40°F)

·

215°C (419°F)




Post-procedure1

a.

Turn the power switch off.



A

5.READ VALUE USING GTS (CHECK WIRE HARNESS OPEN CIRCUIT)

B

9.READ VALUE USING GTS (CHECK WIRE HARNESS SHORT CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (CHECK WIRE HARNESS OPEN CIRCUIT)

Pre-procedure1

a.

Disconnect the UO1 No. 3 frame wire connector.


b.
A376636C12
1.51,0.24 1.885,0.479 0.375,0.24 0.76,0.927 1.396,1.042 true 0.833,1.302 1.406,1.177 true 0.156,0.177 0.469,0.333 0.313,0.156 10 false *a 1.573,0.292 1.927,0.49 0.354,0.198 10 false UO1 0.469,0.865 0.875,1.063 0.406,0.198 10 false RMT 0.427,1.25 0.979,1.479 0.552,0.229 10 false RMTG
*a Front view of wire harness connector
(to No. 3 frame wire connector)


Connect terminals 1 (RMT) and 8 (RMTG) of the UO1 No. 3 frame wire connector.


Procedure1

a.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
OK:
Tester Display Condition Specified Condition
Rear Motor Temperature. Terminals UO1-2 (RMT) and UO1-8 (RMTG) connected
Ignition switch ON
215°C


Result:
Result Proceed to
The value of Rear Motor Temperature is 215 °C A
None of the above conditions are met B


HINT:

215°C = 419°F



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the UO1 No. 3 frame wire connector.



A

6.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR)

B

8.INSPECT HYBRID VEHICLE CONTROL ECU
6.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR)
a.
A475628

Check the connection condition of the rear motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C


b.

Install the rear suspension member sub-assembly.



A

7.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A475628N01
1.865,0.135 2.25,0.396 0.385,0.26 1.99,0.198 2.208,0.354 0.219,0.156 10 true U1

Disconnect the U1 rear motor temperature sensor connector.


Procedure1

a.
A385117C97
1.5,0.271 1.927,0.583 0.427,0.313 1.813,1.469 2.146,1.771 true 1.99,0.99 2.396,0.635 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 2.448,0.563 2.865,0.792 0.417,0.229 10 false RMT 2.188,1.74 2.729,2.021 0.542,0.281 10 false RMTG 1.667,0.365 1.917,0.563 0.25,0.198 10 false U1
*a Component without harness connected
(Rear traction motor with transaxle assembly (Rear motor temperature sensor))


Measure the resistance according to the value(s) in the table below.

OK:
Tester Display Switch Condition Specified Condition
U1-2 (RMT) - U1-12 (RMTG) Ignition switch off 0.3443 to 1446 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the U1 rear motor temperature sensor connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

8.INSPECT HYBRID VEHICLE CONTROL ECU

Pre-procedure1

a.

Connect terminals 54 (RMT) and 53 (RMTG) of the H44 hybrid vehicle control ECU connector.

A458550C04
4.646,0.229 5.094,0.51 0.448,0.281 4.135,1.646 4.427,2.354 true 4.01,1.635 3.75,2.354 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 4.771,0.313 5.229,0.51 0.458,0.198 10 false H44 4.427,2.385 4.917,2.635 0.49,0.25 10 false RMTG 3.521,2.385 4.135,2.583 0.615,0.198 10 false RMT
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -



Procedure1

a.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
OK:
Tester Display Condition Specified Condition
Rear Motor Temperature Terminals H44-54 (RMT) and H44-53 (RMTG) connected
Ignition switch ON
215°C


Result:
Result Proceed to
The value of Rear Motor Temperature is 215 °C A
None of the above conditions are met B


HINT:

215°C = 419°F



Post-procedure1

a.

Turn the power switch off.



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

9.READ VALUE USING GTS (CHECK WIRE HARNESS SHORT CIRCUIT)

Pre-procedure1

a.

Disconnect the UO1 No. 3 frame wire connector.


Procedure1

a.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
OK:
Tester Display Switch Condition Specified Condition
Rear Motor Temperature Ignition switch ON -40°C


Result:
Proceed to
OK
NG


HINT:

-40°C = -40°F



Post-procedure1

a.

Turn the power switch off.


b.

Reconnect the UO1 No. 3 frame wire connector.



OK

10.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR)

NG

12.CHECK HARNESS AND CONNECTOR (FLOOR WIRE - HYBRID VEHICLE CONTROL ECU)
10.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR)
a.
A475628

Check the connection condition of the rear motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C


b.

Install the rear suspension member sub-assembly.



A

11.INSPECT REAR TRACTION MOTOR (REAR MOTOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT REAR TRACTION MOTOR (REAR MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A475628N01
1.865,0.135 2.25,0.396 0.385,0.26 1.99,0.198 2.208,0.354 0.219,0.156 10 true U1

Disconnect the U1 rear motor temperature sensor connector.


Procedure1

a.
A385117C97
1.5,0.271 1.927,0.583 0.427,0.313 1.813,1.469 2.146,1.771 true 1.99,0.99 2.396,0.635 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 2.448,0.563 2.865,0.792 0.417,0.229 10 false RMT 2.188,1.74 2.729,2.021 0.542,0.281 10 false RMTG 1.667,0.365 1.917,0.563 0.25,0.198 10 false U1
*a Component without harness connected
(Rear traction motor with transaxle assembly (Rear motor temperature sensor))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Display Switch Condition Specified Condition
U1-2 (RMT) - U1-12 (RMTG) Ignition switch off 0.3443 to 1446 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the U1 rear motor temperature sensor connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (FLOOR WIRE - HYBRID VEHICLE CONTROL ECU)

Pre-procedure1

a.

Disconnect the UO1 No. 3 frame wire connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458548C01
1.573,0.125 1.969,0.396 0.396,0.271 3.594,0.719 3.99,0.99 0.396,0.271 5.708,1.458 5.885,1.219 true 1.125,1.125 1.552,0.948 true 1.052,0.708 1.542,0.833 true 6.208,1.469 6.031,1.219 true 0.229,0.135 0.542,0.333 0.313,0.198 10 false *a 3.677,0.146 3.99,0.344 0.313,0.198 10 false *b 1.656,0.188 2.01,0.406 0.354,0.219 10 false UO1 3.688,0.792 4.042,1.01 0.354,0.219 10 false H44 0.76,0.635 1.219,0.833 0.458,0.198 10 false RMT 0.729,1.083 1.188,1.281 0.458,0.198 10 false RMTG 6.229,1.49 6.688,1.688 0.458,0.198 10 false RMT 5.375,1.49 5.833,1.688 0.458,0.198 10 false RMTG
*a Front view of wire harness connector
(to No. 3 frame Wire Connector)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Resistance (Check for Open):
Tester Display Switch Condition Specified Condition
UO1-2 (RMT) - H44-54 (RMT) Ignition switch off Below 1 Ω
UO1-8 (RMTG) - H44-53 (RMTG) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Display Switch Condition Specified Condition
UO1-2 (RMT) or H44-54 (RMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
UO1-8 (RMTG) or H44-53 (RMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the H44 hybrid vehicle control ECU connector.


b.

Reconnect the UO1 No. 3 frame wire connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR