Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch Snow Mode Circuit  


DESCRIPTION

When the SNOW mode switch (NO. 2 combination switch assembly) is operated, the SNOW mode signal is sent to the hybrid vehicle control ECU, and drive torque is controlled so that operability is improved in response to operation of the accelerator pedal by the driver when driving on slippery roads, etc.

WIRING DIAGRAM

A434783E05
1.01,1.24 3.042,1.552 2.031,0.313 10 false Combination Meter Assembly 3.656,1.229 4.896,1.688 1.24,0.458 10 false ECM 4.99,3.875 6.823,4.365 1.833,0.49 10 false Hybrid Vehicle Control ECU 1.51,3.833 3.49,4.229 1.979,0.396 10 false SNOW Mode Switch ( NO. 2 Combination Switch Assembly) 0.896,4.333 2.969,4.583 2.073,0.25 10 false : CAN Communication Line 5.438,2.635 6.01,2.854 0.573,0.219 10 false SNOW 5.448,3.125 6.021,3.344 0.573,0.219 10 false NORM 4.99,3.719 5.448,4.031 0.458,0.313 10 false H44 5.156,2.51 5.385,2.708 0.229,0.198 10 false 36 5.156,3.01 5.438,3.25 0.281,0.24 10 false 38 3.531,2.51 3.74,2.75 0.208,0.24 10 false 4 3.521,3.042 3.74,3.271 0.219,0.229 10 false 5 3.292,3.01 3.448,3.208 0.156,0.198 10 false B 3.146,2.521 3.521,2.771 0.375,0.25 10 false 2ND 2.542,2.385 3.052,2.688 0.51,0.302 10 false SNOW 2.49,2.865 3.177,3.188 0.688,0.323 10 false NORMAL 1.813,3 2.24,3.302 0.427,0.302 10 false GND 1.625,3 1.802,3.271 0.177,0.271 10 false 3 1.51,3.667 1.938,3.969 0.427,0.302 10 false H134

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)

A

2.CHECK DTC OUTPUT (HEALTH CHECK)

B

2.CHECK DTC OUTPUT (HEALTH CHECK)

A

3.READ VALUE USING GTS (SNOW MODE SWITCH)

B

GO TO DTC CHART

3.READ VALUE USING GTS (SNOW MODE SWITCH)
a.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Snow Mode Switch Snow mode switch (NO. 2 combination switch assembly) condition ON or OFF Snow mode switch (NO. 2 combination switch assembly) not operated: OFF
Snow mode switch (No. 2 satellite switch set) being pushed and held: ON
Powertrain > Hybrid Control > Data List
Tester Display
Snow Mode Switch
50003 397 507
Result:
Result Proceed to
The display changes according to the snow mode switch (NO. 2 combination switch assembly) operation. A
The display does not change according to the snow mode switch (NO. 2 combination switch assembly) operation. B



b.

Turn the ignition switch off.



A

B

4.INSPECT SNOW MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY)
4.INSPECT SNOW MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY)

OK

5.CHECK HARNESS AND CONNECTOR (SNOW MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE NO. 2 COMBINATION SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SNOW MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the H134 snow mode switch (NO. 2 combination switch assembly) connector.


b.
A475906C01
1.479,0.167 1.969,0.531 0.49,0.365 1.302,1.771 1.49,1.302 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.052,1.771 1.417,1.969 0.365,0.198 10 false GND 1.583,0.292 1.927,0.448 0.344,0.156 10 false H134
*a Front view of wire harness connector
(to Snow Mode Switch (NO. 2 Combination Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H134)Location & Routing

Click Connector(H134)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Combination Switch Assembly

H134-3 (E) - Body ground Always Below 1 Ω



c.

Reconnect the H134 snow mode switch (NO. 2 combination switch assembly) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SNOW MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SNOW MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H134 snow mode switch (No. 2 combination switch assembly) connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.
A475905C01
1.427,0.188 1.927,0.521 0.5,0.333 1.469,2.292 1.969,2.625 0.5,0.333 1.458,1.813 1.615,1.323 true 2.052,3.677 1.698,4.24 true 1.958,1.792 1.792,1.313 true 2.365,3.656 2.708,4.25 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.135,2.177 0.448,2.375 0.313,0.198 10 false *b 1.25,1.844 1.74,2.01 0.49,0.167 10 false 2ND 1.385,4.292 1.875,4.458 0.49,0.167 10 false SNOW 1.531,0.281 1.958,0.469 0.427,0.188 10 false H134 1.604,2.385 1.938,2.563 0.333,0.177 10 false H44 1.969,1.833 2.458,2 0.49,0.167 10 false B 2.667,4.292 3.156,4.458 0.49,0.167 10 false NORM
*a Front view of wire harness connector
(to Snow Mode Switch (NO. 2 Combination Switch Assembly))
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H134,H44)Location & Routing

Click Connector(H134)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Combination Switch Assembly

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H134-4 (2ND) - H44-36 (SNOW) Always Below 1 Ω
H134-5 (B) -H44-38 (NORM) Always Below 1 Ω
H134-4 (2ND) or H44-36 (SNOW) - Body ground Always 10 kΩ or higher
H134-5 (B) or H44-38 (NORM) - Body ground Always 10 kΩ or higher



d.

Reconnect the H44 hybrid vehicle control ECU connector.


e.

Reconnect the H134 snow mode switch (No. 2 combination switch assembly) connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR