Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  TRAIL Switch Circuit  


DESCRIPTION

The TRAIL mode signal will be sent to the hybrid vehicle control ECU when the TRAIL mode switch (NO. 2 combination switch assembly) is operated. If the specified conditions are met, the system enters TRAIL mode and the vehicle will be driven using TRAIL mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the TRAIL indicator.

WIRING DIAGRAM

A434783E07
1.01,1.24 3.042,1.552 2.031,0.313 10 false Combination Meter Assembly 3.656,1.229 4.896,1.688 1.24,0.458 10 false ECM 4.99,3.875 6.823,4.365 1.833,0.49 10 false Hybrid Vehicle Control ECU 1.51,3.833 3.49,4.229 1.979,0.396 10 false SNOW Mode Switch ( No. 2 Combination Switch Assembly) 0.896,4.333 2.969,4.583 2.073,0.25 10 false : CAN Communication Line 5.438,2.635 5.865,2.938 0.427,0.302 10 false ALSD 5.427,3.125 5.99,3.417 0.563,0.292 10 false NORM 4.99,3.719 5.448,4.031 0.458,0.313 10 false H44 5.156,2.49 5.385,2.688 0.229,0.198 10 false 51 5.156,3 5.438,3.24 0.281,0.24 10 false 38 3.531,2.51 3.74,2.75 0.208,0.24 10 false 6 3.531,3.01 3.75,3.24 0.219,0.229 10 false 5 3.281,3 3.438,3.198 0.156,0.198 10 false B 3.281,2.51 3.563,2.76 0.281,0.25 10 false B 2.573,2.396 3.083,2.698 0.51,0.302 10 false TRAIL 2.458,2.865 3.167,3.188 0.708,0.323 10 false NORMAL 1.813,2.99 2.24,3.292 0.427,0.302 10 false GND 1.604,3 1.781,3.271 0.177,0.271 10 false 3 1.51,3.667 1.938,3.969 0.427,0.302 10 false H134

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Check the CAN Bus Check.

CAN Bus Check
50007
Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B



b.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (HEALTH CHECK)

B

2.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



b.

Turn the ignition switch off.



A

3.READ VALUE USING GTS (AUTO LSD SWITCH)

B

GO TO DTC CHART

3.READ VALUE USING GTS (AUTO LSD SWITCH)
a.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Auto LSD Switch TRAIL switch (integration control and panel assembly) condition ON or OFF TRAIL mode switch (integration control and panel assembly) being pushed and held:
ON
TRAIL mode switch (integration control and panel assembly) not operated:
OFF
Powertrain > Hybrid Control > Data List
Tester Display
Auto LSD Switch
50003 397 646
Result:
Result Proceed to
The tester display changes according to the TRAIL mode switch operation. A
The tester display does not change according to the TRAIL mode switch operation. B



b.

Turn the ignition switch off.



A

B

4.INSPECT TRAIL MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY)
4.INSPECT TRAIL MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY)

OK

5.CHECK HARNESS AND CONNECTOR (TRAIL MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE NO. 2 COMBINATION SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (TRAIL MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the H134 TRAIL mode switch (NO. 2 combination switch assembly) connector.


b.
A475906C01
1.479,0.167 1.969,0.531 0.49,0.365 1.302,1.771 1.49,1.302 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.052,1.771 1.417,1.969 0.365,0.198 10 false GND 1.583,0.292 1.927,0.448 0.344,0.156 10 false H134
*a Front view of wire harness connector
(to TRAIL Mode Switch (NO. 2 Combination Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H134)Location & Routing

Click Connector(H134)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Combination Switch Assembly

H134-3 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the H134 TRAIL mode switch (NO. 2 combination switch assembly) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (TRAIL MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRAIL MODE SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H134 TRAIL mode switch (NO. 2 combination switch assembly) connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.
A475905C02
1.427,0.188 1.927,0.521 0.5,0.333 1.469,2.292 1.969,2.625 0.5,0.333 1.458,1.813 1.781,1.313 true 2.25,3.792 1.802,4.271 true 2.271,1.792 1.969,1.313 true 2.365,3.656 2.708,4.25 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.135,2.177 0.448,2.375 0.313,0.198 10 false *b 1.354,1.844 1.844,2.01 0.49,0.167 10 false B 1.563,4.292 2.052,4.458 0.49,0.167 10 false ALSD 1.531,0.281 1.958,0.469 0.427,0.188 10 false H134 1.604,2.385 1.938,2.563 0.333,0.177 10 false H44 2.281,1.813 2.771,1.979 0.49,0.167 10 false B 2.667,4.292 3.156,4.458 0.49,0.167 10 false NORM
*a Front view of wire harness connector
(to TRAIL Mode Switch (NO. 2 Combination Switch Assembly))
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H134,H44)Location & Routing

Click Connector(H134)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Combination Switch Assembly

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H134-6 (B) - H44-51 (ALSD) Always Below 1 Ω
H134-5 (B) - H44-38 (NORM) Always Below 1 Ω
H134-6 (B) or H44-51 (ALSD) - Body ground Always 10 kΩ or higher
H134-5 (B) or H44-38 (NORM) - Body ground Always 10 kΩ or higher



d.

Reconnect the H134 TRAIL mode switch (NO. 2 combination switch assembly) connector.


e.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR