Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Rear Motor Resolver Circuit  


DESCRIPTION

The cause of this malfunction may be the rear motor resolver.

Check the rear motor resolver internal resistance and the connection condition from the rear inverter to the rear motor resolver.

Related Parts Check
Area Inspection
Wire harness and connector between the rear inverter and rear motor resolver Check for short circuit between wire harness and +B side.
Resolver, wire harness, connector Check the resolver internal resistance (include wire harness), body ground resistance, and connector connection condition.
Resolver Check for open or short circuit in wire harness.

SYSTEM DESCRIPTION

The resolver is a sensor that is used to detect the position of the magnetic poles of the rotor of the rear motor. Knowing the position of the poles is indispensable for ensuring precise control of the rear motor. Each resolver contains a stator that has an excitation coil and 2 detection coils (S, C). The gap between the stator and rotor changes as the rotor turns because the rotor is oval shaped. An alternating current with a predetermined frequency flows through the excitation coil, and detection coils S and C output alternating currents in accordance with the sensor rotor position.

The rear motor generator control ECU (Rr MG ECU), which is built into the hybrid motor control rear inverter assembly, detects the absolute position of the rotor according to the phases of detection coils S and C and the heights of their waveforms. Furthermore, the CPU calculates the amount of change in the position within a predetermined length of time, in order to use the resolver as a revolution speed sensor.

The rear motor generator control ECU (Rr MG ECU), which is built into the hybrid motor control rear inverter assembly, monitors signals output from the rear motor resolver and detects malfunctions.

A221242E07
1.406,3.25 0.76,4.542 false 2.229,3.667 1.76,4.844 false 4.5,2.104 4.333,2.417 false 4.521,3.552 3.917,4.156 false 1.323,3.469 1.51,3.719 0.188,0.25 10 -S 1.729,2.188 1.917,2.438 0.188,0.25 10 -S 0.875,2.677 1.115,2.885 0.24,0.208 10 +S 2.156,3.052 2.417,3.25 0.26,0.198 10 +S 1.198,2.219 1.385,2.427 0.188,0.208 10 -C 1.813,3.458 2,3.667 0.188,0.208 10 -C 0.865,3.188 1.073,3.396 0.208,0.208 10 +C 2.135,2.552 2.344,2.76 0.208,0.208 10 +C 0.542,4.563 1.01,4.792 0.469,0.229 10 Rotor 1.323,4.875 2.302,5.115 0.979,0.24 10 Excitation Coil 6.01,0.313 6.99,0.552 0.979,0.24 10 Excitation Coil 5.969,2.031 7.125,2.271 1.156,0.24 10 Detection Coil S 5.969,3.5 7.083,3.74 1.115,0.24 10 Detection Coil C 4.542,2.01 5.646,2.26 1.104,0.25 10 Virtual Waveform 4.552,3.469 5.656,3.719 1.104,0.25 10 Virtual Waveform

WIRING DIAGRAM

A373487E11
5.229,3.104 7.115,3.625 1.885,0.521 10 false Rear Hybrid Motor Control Inverter Assembly (MGR ECU) 4.906,3.104 5.615,3.271 0.708,0.167 10 false O75 0.469,2.49 1.177,2.656 0.708,0.167 10 false U1 0.469,2.625 1.771,2.792 1.302,0.167 10 false Rear Motor Resolver 0.281,3.042 2.427,3.396 2.146,0.354 10 false Rear Traction Motor with Transaxle Assembly 5.938,0.385 6.781,0.823 0.844,0.438 10 false Oscillation Circuit 2.896,2.49 3.979,2.729 1.083,0.24 10 false UO1 3.031,2.125 3.531,2.302 0.5,0.177 10 false RCSG 3.083,1.802 3.406,1.969 0.323,0.167 10 false RCS 3.042,1.479 3.563,1.656 0.521,0.177 10 false RSNG 3.073,1.146 3.396,1.313 0.323,0.167 10 false RSN 3.031,0.823 3.458,0.99 0.427,0.167 10 false RRFG 3.063,0.5 3.385,0.667 0.323,0.167 10 false RRF 1.896,0.49 2.219,0.656 0.323,0.167 10 false RRF 5.281,0.479 5.604,0.646 0.323,0.167 10 false RRF 1.802,0.833 2.229,1 0.427,0.167 10 false RRFG 5.281,0.823 5.708,0.99 0.427,0.167 10 false RRFG 1.865,1.156 2.188,1.323 0.323,0.167 10 false RSN 5.292,1.25 5.615,1.417 0.323,0.167 10 false RSN 1.802,1.479 2.323,1.656 0.521,0.177 10 false RSNG 5.302,1.594 5.823,1.771 0.521,0.177 10 false RSNG 1.865,1.813 2.188,1.979 0.323,0.167 10 false RCS 5.302,1.917 5.625,2.083 0.323,0.167 10 false RCS 5.302,2.25 5.802,2.427 0.5,0.177 10 false RCSG 1.771,2.135 2.271,2.313 0.5,0.177 10 false RCSG 5.292,2.823 5.792,3 0.5,0.177 10 false DRN8 5.063,0.49 5.313,0.677 0.25,0.188 10 false 1 5.052,0.823 5.313,0.99 0.26,0.167 10 false 6 5.063,1.135 5.323,1.302 0.26,0.167 10 false 4 5.063,1.458 5.323,1.625 0.26,0.167 10 false 9 5.073,1.802 5.333,1.969 0.26,0.167 10 false 5 5.01,2.115 5.271,2.281 0.26,0.167 10 false 10 5.052,2.698 5.313,2.865 0.26,0.167 10 false 8 3.521,0.49 3.771,0.677 0.25,0.188 10 false 6 2.813,0.49 3.063,0.677 0.25,0.188 10 false 6 3.521,0.823 3.781,0.99 0.26,0.167 10 false 5 2.813,0.823 3.073,0.99 0.26,0.167 10 false 5 3.531,1.156 3.792,1.323 0.26,0.167 10 false 4 2.813,1.167 3.073,1.333 0.26,0.167 10 false 4 3.5,1.5 3.76,1.667 0.26,0.167 10 false 13 2.76,1.479 3.021,1.646 0.26,0.167 10 false 13 3.5,1.802 3.76,1.969 0.26,0.167 10 false 12 2.76,1.802 3.021,1.969 0.26,0.167 10 false 12 3.5,2.135 3.76,2.302 0.26,0.167 10 false 11 2.76,2.135 3.021,2.302 0.26,0.167 10 false 11 2.24,0.49 2.5,0.656 0.26,0.167 10 false 5 2.24,0.833 2.5,1 0.26,0.167 10 false 8 2.24,1.156 2.5,1.323 0.26,0.167 10 false 3 2.24,1.479 2.5,1.646 0.26,0.167 10 false 4 2.229,1.823 2.49,1.99 0.26,0.167 10 false 9 2.208,2.135 2.469,2.302 0.26,0.167 10 false 13 2.917,2.688 3.979,3.146 1.063,0.458 10 false Floor Wire Connector 0.5,0.365 1.583,0.573 1.083,0.208 10 false Excitation Coil

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.

·

If the resolver is malfunctioning, the vehicle may not drive smoothly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - REAR MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the rear hybrid motor control inverter assembly connector.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
A376642C13
0.385,1.021 0.781,1.292 0.396,0.271 1.833,1 2.219,0.333 true 2,1.021 2.479,0.688 true 2.01,1.229 2.427,1.469 true 1.823,1.24 2.167,1.792 true 1.417,1.24 1.063,1.688 true 1.396,1.01 1.052,0.698 true 0.135,0.156 0.448,0.313 0.313,0.156 10 false *a 0.469,1.094 0.823,1.25 0.354,0.156 10 false O75 0.813,0.542 1.125,0.781 0.313,0.24 10 false RRF 0.833,1.729 1.333,1.969 0.5,0.24 10 false RRFG 2.281,0.177 2.594,0.417 0.313,0.24 10 false RSN 2.208,1.865 2.771,2.094 0.563,0.229 10 false RSNG 2.531,0.615 2.917,0.854 0.385,0.24 10 false RCS 2.542,1.458 3.031,1.698 0.49,0.24 10 false RCSG
*a Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O75)Location & Routing

Click Connector(O75)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O75-1 (RRF) - Body ground Ignition switch ON Below 1 V
O75-6 (RRFG) - Body ground Ignition switch ON Below 1 V
O75-4 (RSN) - Body ground Ignition switch ON Below 1 V
O75-9 (RSNG) - Body ground Ignition switch ON Below 1 V
O75-5 (RCS) - Body ground Ignition switch ON Below 1 V
O75-10 (RCSG) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the low voltage connector of the hybrid motor control inverter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the hybrid motor control inverter assembly connector.



OK

2.CHECK REAR MOTOR RESOLVER (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK REAR MOTOR RESOLVER (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the rear hybrid motor control inverter assembly connector.


Procedure1

a.
A376642C13
0.385,1.021 0.781,1.292 0.396,0.271 1.833,1 2.219,0.333 true 2,1.021 2.479,0.688 true 2.01,1.229 2.427,1.469 true 1.823,1.24 2.167,1.792 true 1.417,1.24 1.063,1.688 true 1.396,1.01 1.052,0.698 true 0.135,0.156 0.448,0.313 0.313,0.156 10 false *a 0.469,1.094 0.823,1.25 0.354,0.156 10 false O75 0.813,0.542 1.125,0.781 0.313,0.24 10 false RRF 0.833,1.729 1.333,1.969 0.5,0.24 10 false RRFG 2.281,0.177 2.594,0.417 0.313,0.24 10 false RSN 2.208,1.865 2.771,2.094 0.563,0.229 10 false RSNG 2.531,0.615 2.917,0.854 0.385,0.24 10 false RCS 2.542,1.458 3.031,1.698 0.49,0.24 10 false RCSG
*a Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O75)Location & Routing

Click Connector(O75)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O75-1 (RRF) - O75-6 (RRFG) Ignition switch off 9.1 to 15.0 Ω
O75-4 (RSN) - O75-9 (RSNG) Ignition switch off 16.4 to 28.3 Ω
O75-5 (RCS) - O75-10 (RCSG) Ignition switch off 18.4 to 30.2 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O75)Location & Routing

Click Connector(O75)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O75-1 (RRF) or O75-6 (RRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
O75-4 (RSN) or O75-9 (RSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
O75-5 (RCS) or O75-10 (RCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the rear hybrid motor control inverter assembly connector.



OK

REAR MOTOR RESOLVER CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

3.CHECK CONNECTOR CONNECTION (FLOOR WIRE CONNECTOR)
3.CHECK CONNECTOR CONNECTION (FLOOR WIRE CONNECTOR)
a.
A475627

Check the connection condition of the rear motor resolver connector (floor wire connector) and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C




A

4.REAR MOTOR RESOLVER (FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REAR MOTOR RESOLVER (FLOOR WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the floor wire connector.


Procedure1

a.
A475627N01
1.729,1.49 2.167,1.771 0.438,0.281 1.813,1.552 2.146,1.729 0.333,0.177 10 true UO1

A376637C20
0.417,0.979 0.833,1.25 0.417,0.271 1.438,1.219 1.344,1.792 true 1.313,1.208 1.021,1.677 true 1.854,0.24 1.729,0.24 1.729,0.24 1.458,1.052 true 2.021,1.792 1.604,1.208 true 1.292,1.042 1.052,0.375 1.052,0.375 0.927,0.375 true 1.594,1.073 1.865,0.542 1.865,0.542 1.969,0.542 true 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a 0.51,1.052 0.854,1.281 0.344,0.229 10 false UO1 2.031,0.5 2.375,0.729 0.344,0.229 10 false RSN 0.698,1.698 1.146,1.958 0.448,0.26 10 false RSNG 1.188,1.823 1.5,1.99 0.313,0.167 10 false RCS 2.021,1.833 2.521,2.01 0.5,0.177 10 false RCSG 0.656,0.323 1.115,0.583 0.458,0.26 10 false RRF 1.917,0.198 2.375,0.365 0.458,0.167 10 false RRFG
*a Front view of floor wire connector
(to Floor Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(UO1)Location & Routing

Click Connector(UO1)Body>No. 6 Floor Wire>No. 6 Floor Wire and Floor Wire

UO1-6 (RRF) - UO1-5 (RRFG) Ignition switch off 8.8 to 14.7 Ω
UO1-4 (RSN) - UO1-13 (RSNG) Ignition switch off 16.1 to 27.9 Ω
UO1-12 (RCS) - UO1-11 (RCSG) Ignition switch off 18.1 to 29.9 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(UO1)Location & Routing

Click Connector(UO1)Body>No. 6 Floor Wire>No. 6 Floor Wire and Floor Wire

UO1-6 (RRF) or UO1-5 (RRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
UO1-4 (RSN) or UO1-13 (RSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
UO1-12 (RCS) or UO1-11 (RCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the floor wire connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

5.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR)
a.
A475628

Check the connection condition of the rear motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.INSPECT FLOOR WIRE (FLOOR WIRE - REAR MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FLOOR WIRE (FLOOR WIRE - REAR MOTOR RESOLVER)

Pre-procedure1

a.
A475628N01
1.865,0.135 2.25,0.396 0.385,0.26 1.99,0.198 2.208,0.354 0.219,0.156 10 true U1

Disconnect the floor wire connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A373486C13
3.708,0.771 4.115,1.021 0.406,0.25 0.51,0.729 0.917,0.99 0.406,0.26 5.323,0.76 5.688,0.375 true 5.188,0.75 5.396,0.188 true 5.063,0.76 4.771,0.188 true 5.042,0.896 4.531,0.427 true 5.969,0.708 5.208,0.927 true 5.938,1.323 5.208,1.063 true 2.698,0.333 2.583,0.333 2.583,0.333 1.885,0.802 true 2.542,1.427 1.885,0.969 true 2.115,0.198 2.01,0.198 2.01,0.198 1.719,0.802 true 2.063,1.552 1.74,0.969 true 1.313,0.302 1.427,0.302 1.427,0.302 1.573,0.802 true 1.302,1.313 1.583,0.958 true 0.656,0.208 0.969,0.365 0.313,0.156 10 false *a 3.802,0.167 4.115,0.323 0.313,0.156 10 false *b 0.604,0.792 0.969,0.958 0.365,0.167 10 false UO1 3.844,0.833 4.052,0.969 0.208,0.135 10 false U1 1.031,0.25 1.49,0.448 0.458,0.198 10 false RRF 2.177,0.156 2.635,0.354 0.458,0.198 10 false RRFG 2.75,0.281 3.208,0.479 0.458,0.198 10 false RSN 0.927,1.313 1.385,1.51 0.458,0.198 10 false RSNG 2.115,1.552 2.573,1.729 0.458,0.177 10 false RCS 2.594,1.427 3.052,1.625 0.458,0.198 10 false RCSG 5.75,0.281 6.208,0.479 0.458,0.198 10 false RRF 4.177,0.313 4.635,0.51 0.458,0.198 10 false RRFG 4.49,0.073 4.948,0.271 0.458,0.198 10 false RSN 5.448,0.073 5.906,0.271 0.458,0.198 10 false RSNG 6.042,0.625 6.5,0.823 0.458,0.198 10 false RCS 6,1.302 6.458,1.5 0.458,0.198 10 false RCSG
*a Front view of wire harness connector (floor wire)
(to floor wire)
*b Front view of wire harness connector (floor wire)
(to rear traction motor)


Standard Resistance (check for open):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(UO1,U1)Location & Routing

Click Connector(UO1)Body>No. 6 Floor Wire>No. 6 Floor Wire and Floor Wire

Click Connector(U1)Body>No. 6 Floor Wire>Rear Traction with Transaxle Motor Assembly

UO1-6 (RRF) - U1-5 (RRF) Ignition switch off Below 1 Ω
UO1-5 (RRFG) - U1-8 (RRFG) Ignition switch off Below 1 Ω
UO1-4 (RSN) - U1-3 (RSN) Ignition switch off Below 1 Ω
UO1-13 (RSNG) - U1-4 (RSNG) Ignition switch off Below 1 Ω
UO1-12 (RCS) - U1-9 (RCS) Ignition switch off Below 1 Ω
UO1-11 (RCSG) - U1-13 (RCSG) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(UO1,U1)Location & Routing

Click Connector(UO1)Body>No. 6 Floor Wire>No. 6 Floor Wire and Floor Wire

Click Connector(U1)Body>No. 6 Floor Wire>Rear Traction with Transaxle Motor Assembly

UO1-6 (RRF) or U1-5 (RRF) - Body ground and other terminals Ignition switch off 1 MΩ or higher
UO1-5 (RRFG) or U1-8 (RRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
UO1-4 (RSN) or U1-3 (RSN) - Body ground and other terminals Ignition switch off 1 MΩ or higher
UO1-13 (RSNG) or U1-4 (RSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
UO1-12 (RCS) or U1-9 (RCS) - Body ground and other terminals Ignition switch off 1 MΩ or higher
UO1-11 (RCSG) or U1-13 (RCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


HINT:

The rear motor resolver is not available as a supply part. If it requires replacement, replace the rear traction motor with transaxle assembly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the floor wire connector.



OK

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE FLOOR WIRE