Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Rear Shut Down Signal Circuit  


DTC SUMMARY

The cause of this malfunction may be a shutdown signal.

Check whether there is an open circuit or a short to +B in the shutdown signal circuit.

Related Parts Check
Area Inspection
Rear inverter, wire harness Check for short to +B in the wire harnesses related to the rear inverter, and check the resistance between the wire harnesses and the body ground.
Wire harness Check for open circuits in the individual wire harnesses.
Inverter Check for inverter malfunction.
Wire harness Check for short circuits in the individual wire harnesses.

DESCRIPTION

Power supply to the motor is cut off due to a shutdown signal sent from the hybrid vehicle control ECU to the rear motor generator control ECU (Rr MG ECU).

WIRING DIAGRAM

A460074E05
4.698,5.24 7.125,5.469 2.427,0.229 10 false Hybrid Motor Control Inverter Assembly 4.698,5.073 4.979,5.24 0.281,0.167 10 false A56 0.167,5.25 3.271,5.521 3.104,0.271 10 false Rear Hybrid Motor Control Inverter Assembly 0.156,5.052 0.438,5.219 0.281,0.167 10 false O74 3.094,3.063 4.927,3.26 1.833,0.198 10 false from PCU FR Fuse 5.219,3.052 5.573,3.229 0.354,0.177 10 false +B 5.208,3.396 5.563,3.573 0.354,0.177 10 false +B2 5.229,3.667 5.865,3.854 0.635,0.188 10 false SDNR 5.208,4.125 5.792,4.313 0.583,0.188 10 false GND1 5.208,4.458 5.927,4.625 0.719,0.167 10 false GND2 5.24,2.24 5.552,2.438 0.313,0.198 10 false H44 4.938,4.573 5.25,4.771 0.313,0.198 10 false 23 4.979,3.188 5.292,3.385 0.313,0.198 10 false 6 4.979,3.531 5.292,3.729 0.313,0.198 10 false 5 4.938,3.927 5.25,4.125 0.313,0.198 10 false 18 4.938,4.24 5.25,4.438 0.313,0.198 10 false 24 1.656,0.521 2.198,0.698 0.542,0.177 10 false +BR1 1.646,0.875 2.219,1.052 0.573,0.177 10 false +BR2 1.656,3.656 2.177,3.833 0.521,0.177 10 false SDNR 1.656,4.125 2.167,4.313 0.51,0.188 10 false GNR1 1.656,4.458 2.208,4.635 0.552,0.177 10 false GNR2 5.26,1.813 5.771,1.979 0.51,0.167 10 false MREL 5.031,1.927 5.344,2.125 0.313,0.198 10 false 47 5.25,2.396 7.031,2.625 1.781,0.229 10 false Hybrid Vehicle Control ECU 2.146,0.646 2.458,0.844 0.313,0.198 10 false 6 2.125,0.99 2.438,1.188 0.313,0.198 10 false 13 2.146,3.927 2.458,4.125 0.313,0.198 10 false 4 2.146,4.229 2.458,4.427 0.313,0.198 10 false 1 2.146,4.573 2.458,4.771 0.313,0.198 10 false 7 2.958,0.646 3.271,0.844 0.313,0.198 10 false 5 3.927,0.646 4.24,0.844 0.313,0.198 10 false 3 3.927,1.938 4.24,2.135 0.313,0.198 10 false 2 2.979,1.938 3.292,2.135 0.313,0.198 10 false 1 3.25,2.115 4.313,2.292 1.063,0.177 10 false PCU RR 4.854,0.667 5.917,0.844 1.063,0.177 10 false PCU-RR 5.979,0.531 6.854,0.917 0.875,0.385 10 false from Auxiliary Battery 4.385,0.531 4.698,0.729 0.313,0.198 10 false O90 4.469,0.302 4.781,0.5 0.313,0.198 10 false 2 4.448,1.031 6.396,1.25 1.948,0.219 10 false Fusible Link Block Assembly

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the hybrid motor control inverter assembly connector.


Procedure1

a.
A365593C80
0.521,0.917 0.948,1.219 0.427,0.302 2.021,1.125 2.542,1.729 true 0.198,0.125 0.51,0.323 0.313,0.198 10 false *a 0.625,0.99 1.083,1.188 0.458,0.198 10 false A56 2.583,1.75 3.042,1.948 0.458,0.198 10 false SDNR
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-18 (SDNR) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the hybrid motor control inverter assembly connector.



OK

2.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
2.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A365592C93
0.969,0.083 1.365,0.365 0.396,0.281 0.979,0.854 0.615,0.583 true 0.813,0.917 0.281,1.031 true 0.854,1.177 1.104,1.844 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.969,1.875 1.583,2.073 0.615,0.198 10 false SDNR 0.073,0.958 0.385,1.156 0.313,0.198 10 false +B 0.313,0.427 0.771,0.625 0.458,0.198 10 false +B2 1.063,0.156 1.354,0.354 0.292,0.198 10 false A56
*a Component without harness connected
(Hybrid Motor Control Inverter Assembly)


Disconnect the hybrid motor control inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-18 (SDNR) - A56-6 (+B) Ignition switch off 5 MΩ or higher
A56-18 (SDNR) - A56-5 (+B2) Ignition switch off 5 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the hybrid motor control inverter assembly connector.



OK

REAR SHUTDOWN SIGNAL CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the hybrid motor control inverter assembly connector.


c.

Disconnect the rear hybrid motor control inverter assembly connector.


Procedure1

a.
A378663C31
0.313,1.177 0.75,1.469 0.438,0.292 0.146,3.406 0.583,3.698 0.438,0.292 2.406,1.927 1.927,1.354 true 2.417,2.594 1.885,3.323 true 2.771,2.979 2.26,3.313 true 2.729,3.99 2.24,3.583 true 0.229,0.188 0.542,0.344 0.313,0.156 10 false *a 0.25,2.615 0.563,2.771 0.313,0.156 10 false *b 2.458,1.958 2.885,2.177 0.427,0.219 10 false SDNR 0.427,1.25 0.719,1.438 0.292,0.188 10 false A56 0.25,3.479 0.854,3.896 0.604,0.417 10 false O74 2.469,2.479 2.896,2.698 0.427,0.219 10 false SDNR 2.833,2.885 3.26,3.104 0.427,0.219 10 false +BR1 2.833,3.979 3.26,4.198 0.427,0.219 10 false +BR2
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)
*b Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-18 (SDNR) - O74-4 (SDNR) Ignition switch off Below 1 Ω
O74-4 (SDNR) - O74-6 (+BR1) Ignition switch off 10 kΩ or higher
O74-4 (SDNR) - O74-13 (+BR2) Ignition switch off 10 kΩ or higher
A56-18 (SDNR) or O74-4 (SDNR) - Body ground Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the rear hybrid motor control inverter assembly connector.


b.

Reconnect the hybrid motor control inverter assembly connector.



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR