| *A | for RH Side | - | - |
| *1 | TRIPOD JOINT | *2 | FRONT AXLE INBOARD JOINT GROMMET |
| *3 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
When using a vise, place aluminum plates between the part and vise.
When using a vise, do not overtighten it.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.INSTALL FRONT AXLE OUTBOARD JOINT BOOT
| *1 | Front Drive Outboard Joint Shaft Assembly | *2 | Front No. 2 Axle Outboard Joint Boot Clamp |
| *3 | Front Axle Outboard Joint Boot | *4 | Front Axle Outboard Joint Boot Clamp |
|
Outboard Joint Side |
|
Inboard Joint Side |
|
Grease | - | - |
Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.
Install new parts to the front drive outboard joint shaft assembly in the following order:
1. Front No. 2 axle outboard joint boot clamp
2. Front axle outboard joint boot
3. Front axle outboard joint boot clamp
Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.
135 to 145 g (4.76 to 5.11 oz)
Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.
Do not allow grease to adhere to the boot clamp track of the outboard joint boot.
Keep the inside of the outboard joint boot free of foreign matter.
43447F
2.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP
|
|
| *a | Fulcrum Point | *b | Lever Push Position |
| *c | Band Support Position | - | - |
Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever at the fulcrum point.
Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.
Check the band and the lever for any deformation before folding back the lever.
The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.
When folding back the lever, do not push at the end of the lever.
| *a | Temporary Claw | - | - |
If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.
| *a | Press down | *b | Contact Point |
| *c | Roll forward | *d | Temporary Claw |
| *e | Fulcrum Point | - | - |
As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.
Do not damage the deflector.
Make sure that the outboard joint is in direct contact with the work surface.
| *a | Buckle | - | - |
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
Do not use excessive force when tapping with the plastic hammer.
Do not damage the front axle outboard joint boot.
43447E
3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP
|
|
| *a | Place the tip near the center of the lever | *b | Buckle |
Install the front axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever.
Set the lever into the guide groove correctly.
Check the band and the lever for any deformation before folding back the lever.
Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.
Do not damage the front axle outboard joint boot.
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.
Do not use excessive force when tapping with the plastic hammer.
Do not damage the front axle outboard joint boot.
43474D
4.INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side)
| *1 | Front Drive Shaft Damper | *2 | Front Drive Shaft Damper Clamp |
Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.
Set the dimension (A) as specified below.
462.5 to 466.5 cm (1.52 to 1.53 ft.)
43474F
5.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side)
| *a | Claw | - | - |
Install the 2 front drive shaft damper clamps to the front drive shaft damper.
Be sure to install the clamps in the correct position.
Using needle-nose pliers, engage each claw to install the 2 front drive shaft damper clamps as shown in the illustration.
Be sure to install the clamps in the correct position.
Do not damage the front drive shaft damper.
Do not damage the claws.
43040
6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
| *1 | Front Axle Inboard Joint Boot Clamp | *2 | Front Axle Inboard Joint Boot |
| *3 | Front No. 2 Axle Inboard Joint Boot Clamp | - | - |
| *a | Protective Tape | *b | Matchmark |
| *c | Groove | - | - |
|
Outboard Joint Side |
|
Inboard Joint Side |
|
Grease | - | - |
Install new parts to the front drive outboard joint shaft assembly in the following order:
1. Front axle inboard joint boot clamp
2. Front axle inboard joint boot
3. Front No. 2 axle inboard joint boot clamp
Remove the protective tape.
Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.
Face the serrated side of the tripod joint outward and install it to the outboard joint end.
Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.
Do not tap the rollers.
Keep the tripod joint free of foreign matter.
Be sure to install the tripod joint in the correct direction.
Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.
Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.
168 to 178 g (5.93 to 6.28 oz)
Install a new front axle inboard joint grommet to the inboard joint groove.
Securely fit the protrusion on the front axle inboard joint grommet into the inboard joint groove.
Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.
7.INSTALL FRONT AXLE INBOARD JOINT BOOT
Install the front axle inboard joint boot to the front drive inboard joint assembly.
Keep the grooves free of grease.
Keep the inside of the front axle inboard joint boot free of foreign matter.
43448F
8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
|
|
| *a | Place the tip near the center of the lever | *b | Buckle |
Install the front axle inboard joint boot clamp to the front axle inboard joint boot and temporarily fold back the lever.
Set the lever into the guide groove correctly.
Check the band and the lever for any deformation before folding back the lever.
Using water pump pliers, pinch the front axle inboard joint boot clamp to temporarily secure it.
Do not damage the front axle inboard joint boot.
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.
Do not use excessive force when tapping with the plastic hammer.
Do not damage the front axle inboard joint boot.
43448G
9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
|
|
| *1 | Front Axle Inboard Joint Grommet | *2 | Front No. 2 Axle Inboard Joint Boot Clamp |
| *a | Recessed Parts | *b | Fulcrum Point |
Adjust dimension (A) until it is within the specified length.
| for LH Side | 621.9 to 629.9 mm (2.04 to 2.07 ft.) |
| for RH Side | 836.9 to 844.9 mm (2.75 to 2.77 ft.) |
While keeping dimension (A) within the specified length, equalize the pressure within the inboard joint with atmospheric pressure by slightly lifting one of the recessed areas of the front axle inboard joint grommet from the front drive inboard joint assembly.
Set the lever fulcrum point at any point (B) indicated in the illustration.
Perform this work with the inside of the inboard joint kept at atmospheric pressure.
Set the lever into the guide groove correctly and install the clamp as far into the inside of the vehicle as possible.
| *a | Fulcrum Point | *b | Lever Push Position |
| *c | Band Support Position | - | - |
Temporarily fold back the lever at the fulcrum point.
Check the band and the lever for any deformation before folding back the lever.
The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.
When folding back the lever, do not push at the end of the lever.
| *a | Temporary Claw | - | - |
If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.
| *a | Press down | *b | Contact Point |
| *c | Roll forward | *d | Temporary Claw |
| *e | Fulcrum Point | - | - |
As shown in the illustration, while pressing the inboard joint area against the work surface, firmly press the lever into place by rolling the inboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.
Make sure that the inboard joint is in direct contact with the work surface.
Do not damage the front drive shaft dust cover.
| *a | Buckle | - | - |
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
Do not use excessive force when tapping with the plastic hammer.
Do not damage the front axle inboard joint boot.
10.INSPECT FRONT DRIVE SHAFT ASSEMBLY