Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY
RM3700E _52 Drivetrain _094372 DRIVE SHAFT / PROPELLER SHAFT _0444428 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C449592N01
1.896,1.104 2.396,1.604 0.5,0.5 1.354,0.656 1.583,0.323 1.583,0.323 1.75,0.323 false 4.427,2.323 4.667,1.833 4.667,1.833 4.833,1.833 false 5.323,2.833 5.5,2.417 5.5,2.417 5.667,2.417 false 0.667,2.583 0.833,2.583 0.833,2.583 0.99,2.281 false 1.417,3.25 1.583,3.25 1.583,3.25 1.833,2.938 false 2.333,3.833 2.5,3.833 2.5,3.833 2.813,3.51 false 6.354,0.26 6.771,0.26 false 1.521,1.042 1.75,0.708 1.75,0.708 1.917,0.708 false 2.146,1.104 2.375,0.771 2.375,0.771 2.542,0.771 false 3.021,1.698 3.25,1.365 3.25,1.365 3.417,1.365 false 3.615,1.938 3.844,1.604 3.844,1.604 4.01,1.604 false 4.49,4.938 4.656,4.938 4.656,4.938 4.969,4.615 false 6.167,3.49 6.167,3.073 6.167,3.073 6.271,3.073 false 1.229,3.083 1.51,3.438 0.281,0.354 18 false 1 2.094,3.677 2.375,4.031 0.281,0.354 18 false 2 0.479,2.438 0.76,2.792 0.281,0.354 18 false 3 2.135,0.177 2.417,0.531 0.281,0.354 18 false 4 6.635,2.927 6.917,3.281 0.281,0.354 18 false 7 5.875,2.281 6.156,2.635 0.281,0.354 18 false 5 5.385,1.688 5.667,2.042 0.281,0.354 18 false 6 6.167,0.135 6.448,0.49 0.281,0.354 18 false 8 5.26,1.75 5.542,2.083 0.281,0.333 10 false ● 5.74,2.323 6.021,2.656 0.281,0.333 10 false ● 6.521,2.979 6.802,3.313 0.281,0.333 10 false ● 1.938,3.719 2.219,4.052 0.281,0.333 10 false ● 1.104,3.146 1.385,3.479 0.281,0.333 10 false ● 0.344,2.469 0.625,2.802 0.281,0.333 10 false ● 2.604,0.708 2.917,0.906 0.313,0.198 10 false *1 1.958,0.656 2.24,0.99 0.281,0.333 10 false ● 3.469,1.313 3.781,1.51 0.313,0.198 10 false *2 4.063,1.552 4.375,1.75 0.313,0.198 10 false *3 4.313,4.885 4.625,5.083 0.313,0.198 10 false *4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DRIVE SHAFT OUTBOARD JOINT BOOT - (Click here) - -
2 REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP 42346F (Click here) - -
3 REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP 42346D (Click here) - -
4 REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY 42360D (Click here) - -
5 REAR DRIVE SHAFT INBOARD JOINT BOOT - - - -
6 REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP 42347F (Click here) - -
7 REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP 42347D (Click here) - -
8 INSPECT REAR DRIVE SHAFT ASSEMBLY 42340B (Click here) - -

*1 BALL *2 INNER RACE
*3 BALL CAGE *4 REAR DRIVE SHAFT OUTBOARD JOINT SHAFT ASSEMBLY
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT

a.
C439734C01
6.427,0.75 6.219,0.99 false 6.865,0.969 6.74,1.125 false 5.938,0.583 5.656,0.896 false 5.458,0.656 5.177,0.969 false 0.719,0.302 1,0.656 0.281,0.354 18 false i 4.042,0.229 4.323,0.583 0.281,0.354 18 false ii 4.052,2.167 4.333,2.521 0.281,0.354 18 false iv 0.677,2.177 0.958,2.531 0.281,0.354 18 false iii 5.5,0.563 5.813,0.719 0.313,0.156 10 false *1 5.979,0.521 6.292,0.677 0.313,0.156 10 false *2 6.469,0.656 6.781,0.813 0.313,0.156 10 false *3 6.885,0.865 7.073,1.031 0.188,0.167 10 false *4
*1 Rear Drive Shaft Outboard Joint Assembly *2 Rear No. 2 Drive Shaft Outboard Joint Boot Clamp
*3 Rear Drive Shaft Outboard Joint Boot *4 Rear Drive Shaft Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side
V100137

Grease - -


i.

Wrap the splines of the rear drive shaft outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


ii.

Install new parts to the rear drive shaft outboard joint shaft assembly in the following order:

1. Rear No. 2 drive shaft outboard joint boot clamp

2. Rear drive shaft outboard joint boot

3. Rear drive shaft outboard joint boot clamp


iii.

Pack the joint portion of the rear drive shaft outboard joint shaft assembly and rear drive shaft outboard joint boot with grease.

Standard Grease Capacity:

37 to 47 g (1.31 to 1.66 oz)



iv.

Install the rear drive shaft outboard joint boot to the rear drive shaft outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.





Hide 42346F 2.INSTALL REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.
C449597N02
0.427,0.052 0.896,0.375 0.469,0.323 18 false i

i.

Using a screwdriver, install the rear No. 2 drive shaft outboard joint boot clamp as shown in the illustration.

NOTICE:

Be careful not to damage the rear drive shaft outboard joint boot.




Hide 42346D 3.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.
C449593N01
1.063,0.583 1.76,0.896 true 4.604,1.198 5.094,1.198 true 0.438,0.083 1.521,0.448 1.083,0.365 18 false i, ii, iii, iv 0.792,0.51 1.167,0.729 0.375,0.219 10 false SST 4.333,1.135 4.667,1.427 0.333,0.292 10 false SST 4.177,0.063 4.51,0.417 0.333,0.354 18 false v

i.

Install the rear drive shaft outboard joint boot clamp to the rear drive shaft outboard joint boot.


ii.

Place SST onto the rear drive shaft outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


iii.

Tighten SST so that the rear drive shaft outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



iv.

Remove SST.


v.

Using SST, measure the clearance of the rear drive shaft outboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 mm (0.0472 in.) or less


If the clearance is not as specified, retighten SST.



Hide 42360D 4.INSTALL REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY

a.
C449594C01
1.49,2.906 1.958,2.396 1.958,2.396 1.542,2.958 true 1.552,1.563 1.552,1.313 false 0.927,1.396 0.927,1.146 false 2.396,1.667 2.396,1.417 false 2.771,1.333 2.771,1.083 false 0.49,0.125 1.865,0.479 1.375,0.354 18 false i, ii 4.313,0.146 5.688,0.5 1.375,0.354 18 false iii 0.49,1.99 1.865,2.344 1.375,0.354 18 false iv, v 4.115,2.063 5.49,2.417 1.375,0.354 18 false vi 1.927,2.26 2.479,2.604 0.552,0.344 10 false *b 2.698,1.344 3.25,1.688 0.552,0.344 10 false *a 0.854,1.406 1.406,1.75 0.552,0.344 10 false *1 1.479,1.594 2.031,1.938 0.552,0.344 10 false *2 2.333,1.698 2.885,2.042 0.552,0.344 10 false *3
*1 Rear Drive Shaft Inboard Joint Boot Clamp *2 Rear Drive Shaft Inboard Joint Boot
*3 Rear No. 2 Drive Shaft Inboard Joint Boot Clamp - -
*a Protective Tape *b Matchmark
V100135

Outboard joint side
V100136

Inboard joint side


i.

Install new parts to the rear drive shaft outboard joint shaft assembly in the following order:

1. Rear drive shaft inboard joint boot clamp

2. Rear drive shaft inboard joint boot

3. Rear No. 2 drive shaft inboard joint boot clamp


ii.

Remove the protective tape.


iii.

Install the ball cage to the rear drive shaft outboard joint shaft assembly.

NOTICE:

Face the smaller inside diameter side to the rear drive shaft outboard joint shaft assembly.



iv.

Align the matchmarks placed before removal.


v.

Using a brass bar and a hammer, install the inner race to the rear drive shaft outboard joint shaft assembly.

NOTICE:

Be careful not to damage the inner race.



vi.

Using a snap ring expander, install a new shaft snap ring to the rear drive shaft outboard joint shaft assembly.



b.
C449595C01
2.583,1.281 2.948,1.49 2.948,1.49 2.729,1.156 true 2.635,1.229 2.938,1.49 true 5.688,2.625 5.427,2.219 5.427,2.219 5.938,2.375 true 0.552,0.167 0.833,0.521 0.281,0.354 18 false i 4.531,0.177 5.094,0.5 0.563,0.323 18 false ii, iii 0.521,2.083 0.802,2.438 0.281,0.354 18 false iv 4.531,2.063 4.813,2.417 0.281,0.354 18 false v 2.938,1.5 3.219,1.854 0.281,0.354 10 false *a 5.24,2.135 5.521,2.49 0.281,0.354 10 false *a
*a Matchmark - -
V100135

Grease - -


i.

Align the matchmarks and install the ball cage to the inner race.


ii.

Apply grease to the balls to keep them from falling.


iii.

Install the 6 balls with grease to the inner race.

NOTICE:

Be careful not to drop the balls.



iv.

Pack the rear drive shaft inboard joint assembly and rear drive shaft inboard joint boot with grease.

Standard Grease Capacity:

102 to 112 g (3.60 to 3.95 oz.)



v.

Align the matchmarks and install the rear drive shaft inboard joint assembly to the rear drive shaft outboard joint shaft assembly.



Hide 5.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT

Hide 42347F 6.INSTALL REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP

a.
C449596C01
4.26,0.667 4.667,0.729 4.667,0.729 4.906,0.604 false 0.438,0.063 1.813,0.417 1.375,0.354 18 false i 3.51,0.094 4.885,0.448 1.375,0.354 18 false ii 1.656,1.365 1.958,1.573 0.302,0.208 10 false A 4.604,0.75 4.917,0.948 0.313,0.198 10 false *a
*a Claw - -


i.

Check whether the dimension (A) of each drive shaft is within specification.

Dimension (A):

512.1 to 522.1 mm (1.68 to 1.71 ft.)



ii.

Using needle-nose pliers, engage the 2 claws to install the rear No. 2 drive shaft inboard joint boot clamp as shown in the illustration.

NOTICE:

Be careful not to damage the rear drive shaft inboard joint boot.




Hide 42347D 7.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP

a.

Perform the same procedure as for the rear No. 2 drive shaft inboard joint boot clamp.


Hide 42340B 8.INSPECT REAR DRIVE SHAFT ASSEMBLY