Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0441741 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15DB  Telematics Transceiver Disconnected  


DESCRIPTION

If the radio and display receiver assembly cannot detect the telematics transceiver for a certain period of time (90 seconds) after the ignition switch is turned ACC and the radio and display receiver assembly confirms that the information is missing by checking past telematics transceiver recognition information (registered information), this DTC will be stored.

HINT:

The telematics system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the telematics system will not operate normally.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15DB Telematics Transceiver Disconnected Telematics transceiver disconnected
·

Harness or connector

·

Telematics transceiver

·

Radio and display receiver assembly


Navigation System A

HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E450791E01
0.26,0.615 1.167,1 0.906,0.385 10 false from Auxiliary Battery 0.156,1.708 1.146,2.219 0.99,0.51 10 false from IGR-NO. 2 Relay 1.667,0.792 2.125,0.99 0.458,0.198 10 false DCM 1.313,1.865 2.427,2.198 1.115,0.333 10 false ECU-IGR NO. 2 2.625,0.646 3.083,0.844 0.458,0.198 10 false H85 2.625,1.719 3.083,1.917 0.458,0.198 10 false H85 2.719,0.438 2.875,0.635 0.156,0.198 10 false 1 2.688,1.51 2.927,1.708 0.24,0.198 10 false 19 3.01,0.646 3.469,0.844 0.458,0.198 10 false +B 3.01,1.771 3.469,1.969 0.458,0.198 10 false IG2 3.031,2.729 3.49,2.927 0.458,0.198 10 false E 3.531,0.5 4.063,0.719 0.531,0.219 10 false USB+ 3.49,1.344 4.052,1.583 0.563,0.24 10 false USBS 3.469,2.177 4.01,2.385 0.542,0.208 10 false USBV 3.49,2.583 4.052,2.76 0.563,0.177 10 false USBG 2.75,3.104 4.271,3.563 1.521,0.458 10 false Telematics Transceiver 3.958,0.51 4.417,0.708 0.458,0.198 10 false H119 3.969,0.927 4.427,1.125 0.458,0.198 10 false H119 4,2.177 4.458,2.375 0.458,0.198 10 false H85 4,2.594 4.458,2.792 0.458,0.198 10 false H85 4.094,0.302 4.563,0.458 0.469,0.156 10 false 2 4.083,0.729 4.552,0.885 0.469,0.156 10 false 1 4.094,1.156 4.563,1.313 0.469,0.156 10 false 3 4.052,1.969 4.333,2.167 0.281,0.198 10 false 15 4.052,2.396 4.365,2.604 0.313,0.208 10 false 31 4.938,1.104 5.406,1.323 0.469,0.219 10 false * 6.052,0.552 6.51,0.75 0.458,0.198 10 false US4+ 3.51,0.906 3.969,1.104 0.458,0.198 10 false USB- 6.042,0.948 6.5,1.146 0.458,0.198 10 false US4- 6.042,1.333 6.5,1.531 0.458,0.198 10 false USD4 6.042,2.208 6.573,2.396 0.531,0.188 10 false USBV 6.052,2.615 6.594,2.813 0.542,0.198 10 false USBG 5.615,0.51 6.073,0.708 0.458,0.198 10 false H120 5.625,0.927 6.083,1.125 0.458,0.198 10 false H120 5.615,1.323 6.073,1.521 0.458,0.198 10 false H120 5.656,2.188 6.115,2.385 0.458,0.198 10 false H81 5.656,2.594 6.115,2.792 0.458,0.198 10 false H81 5.865,3.094 7.052,3.573 1.188,0.479 10 false Radio and Display Receiver Assembly 5.75,0.344 5.906,0.542 0.156,0.198 10 false 1 5.76,0.74 5.917,0.938 0.156,0.198 10 false 2 5.76,1.135 5.917,1.333 0.156,0.198 10 false 3 5.719,1.969 5.917,2.177 0.198,0.208 10 false 10 5.708,2.396 5.917,2.646 0.208,0.25 10 false 11 1.021,4.323 5.042,4.604 4.021,0.281 10 false : Data Signal (USB Communication Line) 3.969,1.354 4.427,1.552 0.458,0.198 10 false H119 2.635,2.708 3.094,2.906 0.458,0.198 10 false H85 2.688,2.5 2.927,2.698 0.24,0.198 10 false 20 0.427,3.99 4.865,4.188 4.438,0.198 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the telematics transceiver, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for G-BOOK.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch ON and wait for 90 seconds.


c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the H85 telematics transceiver connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H85)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

H85-20 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H85)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

H85-1 (+B) - Body ground Ignition switch off 11 to 14 V
H85-19 (IG2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

Pre-procedure1

a.

Disconnect the radio and display receiver assembly connector.


Procedure1

b.
E367494C89
1.542,0.75 1.958,1.021 0.417,0.271 2.438,2.844 1.844,2.052 true 1.26,2.813 1.531,2.052 true 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a 1.615,0.792 2.052,0.979 0.438,0.188 10 false H81 2.292,2.875 2.906,3.073 0.615,0.198 10 false USBV 1.021,2.875 1.635,3.073 0.615,0.198 10 false USBG
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H81)Location & Routing

Click Connector(H81)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H81-11 (USBG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H81)Location & Routing

Click Connector(H81)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H81-10 (USBV) - H81-11 (USBG) Ignition switch ACC 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

Pre-procedure1

a.

Disconnect the H81 radio and display receiver assembly connector.


b.

Disconnect the H85 telematics transceiver connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H81,H85)Location & Routing

Click Connector(H81)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

H81-10 (USBV) - H85-15 (USBV) Always Below 1 Ω
H81-11 (USBG) - H85-31 (USBG) Always Below 1 Ω
H81-10 (USBV) - Body ground Always 10 kΩ or higher
H81-11 (USBG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - RADIO AND DISPLAY RECEIVER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H119 telematics transceiver connector.


b.

Disconnect the H120 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H119,H120)Location & Routing

Click Connector(H119)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

Click Connector(H120)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H119-1 (USB-) - H120-2 (US4-) Always Below 1 Ω
H119-2 (USB+) - H120-1 (US4+) Always Below 1 Ω
H119-3 (USBS) - H120-3 (USD4) Always Below 1 Ω
H119-1 (USB-) - Body ground Always 10 kΩ or higher
H119-2 (USB+) - Body ground Always 10 kΩ or higher
H119-3 (USBS) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

7.CHECK TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch ON and wait for 90 seconds.


c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (TELEMATICS TRANSCEIVER IS DEFECTIVE)