Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0444808 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model)  C060B13  Left Electric Parking Brake Actuator Control Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C060B13 Left Electric Parking Brake Actuator Control Circuit Open
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (open).

·

Detection Time:

Approximately 1 second


·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>CALIBRATION

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the uO2 and u3 No. 2 parking brake wire assembly connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

C390252C12
1.479,0.135 1.896,0.385 0.417,0.25 5,0.333 5.417,0.583 0.417,0.25 4.521,2.094 4.938,1.677 true 5.823,2.135 5.469,1.688 true 1.573,0.177 2.031,0.375 0.458,0.198 10 false uO2 5.104,0.396 5.563,0.594 0.458,0.198 10 false u3 5.885,2.052 6.302,2.302 0.417,0.25 10 false + 4.396,2.063 4.854,2.26 0.458,0.198 10 false - 1.604,2.563 2.063,2.771 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.25 5.604,2.448 0.458,0.198 10 false *c
*a Front view of No. 2 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly LH) - -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,u3)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

uO2-1 - u3-2 (+) Always Below 1 Ω
uO2-1 - Other terminals Always 10 kΩ or higher
uO2-2 - u3-1 (-) Always Below 1 Ω
uO2-2 - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the u3 parking brake actuator assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A94,u3)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

A94-3 (MRL+) - u3-2 (+) Always Below 1 Ω
A94-2 (MRL-) - u3-1 (-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH