Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0441946 BRAKE ACTUATOR(for Gasoline Model) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442404N02
4.948,0.5 5.281,0.5 false 4.906,1.469 5.24,1.469 false 2.896,0.531 3.229,0.531 false 6.417,0.271 6.729,0.271 false 6.417,0.833 6.688,0.833 false 6.417,1.333 6.729,1.333 false 4.531,2.083 4.865,2.083 false 2.729,3.75 3.063,3.75 false 1.031,2.917 1.365,2.917 false 2.188,5.167 2.521,5.167 false 1.115,4.802 1.448,4.802 false 1.073,3.781 1.406,3.781 false 5.323,0.365 5.604,0.719 0.281,0.354 18 false 3 5.292,1.354 5.573,1.708 0.281,0.354 18 false 5 2.698,0.385 2.979,0.74 0.281,0.354 18 false 4 6.198,0.135 6.729,0.573 0.531,0.438 18 false 1 6.198,0.688 6.729,1.125 0.531,0.438 18 false 2 6.198,1.177 6.448,1.615 0.25,0.438 18 false 7 4.917,1.948 5.167,2.385 0.25,0.438 18 false 6 2.385,0.49 2.75,0.76 0.365,0.271 10 false x12 3.125,3.583 3.458,4 0.333,0.417 18 false 8 1.406,2.76 1.74,3.177 0.333,0.417 18 false 9 1.719,3.615 2.052,4.031 0.333,0.417 18 false 10 2.792,4.25 3.156,4.521 0.365,0.271 10 false x3 1.854,4.99 2.188,5.406 0.333,0.417 18 false 12 1.479,4.635 1.813,5.052 0.333,0.417 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 REMOVE WINDSHIELD WIPER MOTOR AND LINK - - - -
4 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
5 WATER GUARD PLATE LH 55735A - - -
6 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
7 DRAIN BRAKE FLUID - - (Click here) -
8 ECM 89661 - - -
9 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
10 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
11 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
12 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C442405N03
4,0.25 4.583,1.583 0.583,1.333 2.583,0.667 3.333,1.5 0.75,0.833 3.854,1.75 4.5,1.75 false 4.583,0.75 5.167,0.75 false 2.198,1.25 2.583,1.25 false 4.844,1.615 5.135,1.906 0.292,0.292 18 false 14 5.531,0.594 5.906,0.885 0.375,0.292 18 false 13 1.833,1.094 2.208,1.385 0.375,0.292 18 false 13 3.031,2 3.406,2.292 0.375,0.292 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

13 BRAKE LINE - (Click here) - -
14 BRAKE ACTUATOR WITH BRACKET - (Click here) - -

C442406N02
3.042,1.542 3.333,1.542 false 3.125,2.844 3.417,2.844 false 3.292,3.573 3.479,3.573 3.479,3.573 3.625,3.875 false 2.552,4.271 2.844,4.271 false 2.604,4.625 2.896,4.625 false 2.677,1.385 3.229,1.74 0.552,0.354 18 false 16 2.927,2.76 3.177,3.031 0.25,0.271 10 false *1 2.948,3.406 3.333,3.719 0.385,0.313 18 false 15 2.24,4.094 2.625,4.406 0.385,0.313 18 false 18 2.281,4.479 2.667,4.792 0.385,0.313 18 false 17 3.042,4.26 3.292,4.438 0.25,0.177 10 false x3 3.031,4.604 3.281,4.781 0.25,0.177 10 false x3 3,4.927 3.25,5.104 0.25,0.177 10 false x3 4.094,4.969 4.344,5.146 0.25,0.177 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

15 NO. 1 BRAKE ACTUATOR BRACKET 44591 (Click here) - -
16 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
17 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A - - -
18 BRAKE ACTUATOR BRACKET CUSHION 44547B - - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Skid control ECU (brake actuator assembly) Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned ON (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 4.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55735A 5.REMOVE WATER GUARD PLATE LH

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 7.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 9.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 10.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 11.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 12.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 13.SEPARATE BRAKE LINE

a.
C442407C01
2.167,2.885 2.563,3.021 true 1.375,3.208 1.677,3 true 1.25,2.76 1.583,2.76 true 1.26,2.438 1.729,2.708 true 1.927,2.667 2.25,2.323 true 2.104,2.667 2.438,2.667 true 2.604,2.927 2.906,3.156 0.302,0.229 10 true *a 1.083,3.115 1.385,3.344 0.302,0.229 10 true *b 0.958,2.667 1.26,2.896 0.302,0.229 10 true *c 0.958,2.344 1.26,2.573 0.302,0.229 10 true *d 2.24,2.208 2.542,2.438 0.302,0.229 10 true *e 2.438,2.563 2.74,2.792 0.302,0.229 10 true *f 0.5,0.135 0.781,0.417 0.281,0.281 18 true i 4,0.135 4.281,0.417 0.281,0.281 18 true ii 0.469,2 0.75,2.281 0.281,0.281 18 true iii 4,2 4.281,2.281 0.281,0.281 18 true iv
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH *d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH *f To Front Wheel Cylinder Assembly RH
V113147

Release the lock lever - -


i.

Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Using a 10 mm union nut wrench, disconnect the brake line from the front flexible hose.


iii.

Use tags or make a memo to identify the places to reconnect the brake lines.


iv.

Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.



Hide 14.REMOVE BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



a.
C442408N01
0.417,0.052 0.698,0.406 0.281,0.354 18 false i

i.

Remove the bolt, 2 nuts and brake actuator with bracket from the vehicle body.



Hide 44591 15.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C429858


Hide 44510 16.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C442409


Hide 44521A 17.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C442410


Hide 44547B 18.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C442411